Doyson S 400 Gebruikershandleiding

Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Doyson S 400. Doyson S 400 1 pagina's. S series control module

Pagina afdrukken

S 400 USER MANUAL

HOW TO SWITCH ON AND OFF THE CONTROL

MODULE: Press the control module on/off key. The display

will light up and either the audio program or the time will

be shown on it. Press again the on/off key to switch the

control module off.

GENERAL SYSTEM ON/OFF: Pressing simultaneously the

on/off and > keys all the control modules of the multiroom

system will switch on while a flashing "ON" will be shown

on the display.

Pressing simultaneously the on/off and < keys all the control

modules of the multiroom system will switch off while a

flashing "OFF" will be shown on the display.

CHANNEL AND AUXILIARY AUDIO INPUT SELECTOR

Push the CH key to change the audio program. The selected

channel will show on the display.

VOLUME CONTROL: While the control module is on

press the > key to turn the volume up and the < key to

turn the volume down.

CONTROL OF BALANCE AND MONO/STEREO

SOUND

While the control module is on, press repeatedly the MOD

key until the feature you want to adjust is shown on the

display. Then use the keys < and > to regulate the function.

TIME SETUP: Either when the control module is on or

off, press repeatedly the MOD key until the function "SET"

is shown on the display. Set the time using the < > keys.

Once the time is set in one module, the rest of control

modules will automatically be sincronized.

AUTO OFF SETUP: While the control module is on, press

repeatedly the MOD key until the "AUTO OFF" function

is shown on the display. The time countdown for automatic

desconexion will set by pressing the on/off key repeatedly

(time will increase in intervals of 15 minutes) or using the

WIRING DIAGRAM FOR S 400 CONTROL

MODULE AND UC 400 S CENTRAL UNIT

System with central unit

GROUND - Vcc

POWER SUPPLY 12 +Vcc

COMMUNICATIONS

CHANNEL 1

CHANNEL 2

CHANNEL 3

CHANNEL 4

CABLE REF. W-14

MINIMUM SECTION

2X1MM

12X0,25 MM

C4R

C4L

C3R

C3L

C2R

C2L

C1R

C1L

UC 400 S

2x0,75 mm.

RED 230 Vca.

ANTENNA CONNECTION: Conductor wire of 80 cm. In zones of

bad reception, connection to outdoor antenna it is highly recommended.

NOTE.- The UC 400 S supports a máximum of 10 sound control modules and a maximum distance of 100 mts.of cable to the last

element to be controlled. For higher installations, power supply units or a more powerful central unit would be required.

HOW TO PROGRAM THE SYSTEM:

Once all the system units are already installed, a zone number must be assigned to each control module as follows:

1st.- Keep the keys <> pressed during 4 seconds. The number "1" will be shown on the displays of ever y control module.

2nd.- Choose the control module you want to be the "zone 1" and press the On/Off key. The number "1" will be memorized as a zone number in

that control module.

3rd.- Now the rest of control modules will show the number "2" in their displays. Choose again which control module you want to be the "zone 2"

and press the On/Off key of that module.

4th- Repeat the process as many times as control modules/zones are in the installation.

5th- Once the zone assignment is finished, keep the control module on/off key pressed during 4 secondsin order to leave the "assingnment zone mode".

< > keys (time will increase in intervals of 1 minute).

AUTO ON SETUP: While the control module is off, keep

pressed the on/off key until the "AUTO ON" function is

shown on the display. The time countdown for automatic

conexion will set by pressing the on/off key repeatedly

(time will increase in intervals of 15 minutes) or using the

< > keys (time will increase in intervals of 1 minute).

SLEEP MODE: While the control module is on, press

repeatedly the MOD key until the function "SLEEP" is

shown on the display. The switch off time can be set by

pressing the on/off key repeatedly (time will increase in

intervals of 15 minutes) or using the < > keys (time will

increase in intervals of 1 minute).

Another way to activate this function is by keeping pressed

the on/off key during 3 seconds while the control module

is on. When the "SLEEP" mode is shown on the display, the

switch off time can be set by pressing the on/off key

repeatedly (time will increase in intervals of 15 minutes)

or using the < > keys (time will increase in intervals of 1

minute).

ALARM CLOCK SETUP: Either when the control module

is on or off, press repeatedly the MOD key until the

"ALARM" function is shown on the display. Using the < >

keys the alarm time can be set. Immediately after the alarm

mode (CH1, IN or BEEP) can be chosen by pressing the

alarm clock key on the right hand side. The alarm clock

volume can be also preset using the < > keys. A small bell

symbol on the display will show the alarm clock is on.

To switch off the alarm clock when ringing just press any

key.

To deactivate the alarm clock function press repeatedly

the MOD key until the "ALARM" function is shown on the

display. Immediately after press repeatedly the alarm clock

key on the right hand side until "ALARM OFF" is shown

on the display. The bell symbol will not appear on the display

any more.

System with power supply unit

STEREO

ZONE

Speaker

Ref. SP 5

CABLE REF. W-2

MINIMUM SECTION

2X0.50 MM

0 5 8 9

C1 C2 C3 C4

R+ R- L- L+

ANT

S 400

For AUXILIARY CONNECTION of audio, TV, PC, etc. please

use 0 (ground) and C1

STEREO

ZONE

Speaker

Ref. SP 5

CABLE REF. W-2

MINIMUM SECTION

2X0.50 MM

0 5 8 9

C1 C2 C3 C4

R+ R- L- L+

Power supply

unit

FA 12 BI

S 400

The control module memorizes the last alarm clock setting

if no new features are introduced.

CALL RECEPTION AND BABY-PHONE LISTENER

Either when the control module is on or off, calls from

built-in microphone control modules can be received. The

zone number of the zone that is calling will show on the

display "CALL IN + NR".

The S 400 can be activated as a listener control module

in the baby-phone function. After having activated the

control module in the children's bedroom (this must be a

built-in microphone control module) press twice the MOD

key in the listener control when the module is off. "PARENT"

will show on the display. Use the < > keys to activate or

deactivate the listening function.

Up to 5 baby rooms and 5 listening areas can be selected

to be working simultaneously.

The listening volume can be adjusted using the < > keys,

is independent from the program volume and is automatically

memorized by the control module.

DO NOT DISTURB MODE: When the control module

is on, press repeatedly the MOD key until "DONT

DISTURB:OFF" is shown on the display. Press the > key

to activate the "do not disturb" function. DONT

DISTURB:ON" will be shown on the display. From that

moment the control module will not receive any call.

To deactivate this function, repeat the operation and press

the key <. "DONT DISTURB:OFF" will be shown on the

display and from that moment the "do not disturb" mode

will be deactivated.

AUXILIARY AUDIO INPUT (IN): Connect the audio player

jack in the audio socket. Press the auxiliary audio input key

until "IN" is shown on the display.

w w w. d oy s o n . c o m

ANT

S 400 Technical characteristics

Nr. of channels...................................4 mono channel

Amplifier..............................................1.5+1.5W stereo

Minimum load impedance................8 ohms

Power supply......................................12Vcc/330mA

Stand-by power consumption........25mA

Operational power consumption..69mA

Connectors.........................................Strip terminals

Dimensions.........................................44 x 44 x 36mm depth

S o u n d & H o m e

A u t o m a t i o n

CONTROL

MODULE

S 400

ON/OFF KEY

LCD DISPLAY

VOLUME.

CHANNEL AND AUX. IN

SELECTOR

MENU KEY

ALARM CLOCK AND

PARENT FUNCTION

AUXILIARY AUDIO INPUT