Amroad DP101 Snelle installatiehandleiding
Blader online of download pdf Snelle installatiehandleiding voor {categorie_naam} Amroad DP101. Amroad DP101 2 pagina's.
Pagina afdrukken
Package Contents
The following items are included in your Video Door
Phone package. Check this list before installation to
ensure that you have received all items.
1.
Front Panel
2. Video Door Phone Unit
3. Back Plate
4. Screw Pack (4 pieces of M4 x 10mm)
5. Wrench
6. Water Stopper (4 pieces of silicon rubber)
7.
Screw for Earth Wire
8. Wall mounted screw pack
9. Terminal Connector
10. H type Terminal Connector for Power
Wire
11. Tool for removing the Front Panel from
Video Door Phone Unit
12. Relay Board
13. Master RFID Card (For RFID module only)
14. Quick Installation Guide and Quick Start Guide
(English and Chinese versions)
Please contact your dealer immediately if items are
missing.
Rear Panel
The Alarm Sensor is burglarproof function, it will send out the louder warning sound from speaker when
Alarm Sensor is triggered!
WARNING: DO NOT connect the AC power Until DP101/R is deployed on the wall.
Installing Video Door Phone
Suggested Installation Positions
Due to the view angle of the camera is limited,
therefore the installation position for Video Door
Phone is crucial. In order to get a better view, the
view angle of this door phone should be around
o
105
. Also the height of the lens position is
suggested around 155cm according to building
conditions. For more details please refer to Figure
right.
WARNING: Avoid eyes exposure to the beam of the
WL (White Light) LED for a long time, or it may
cause discomfort to your eyes.
800-0000012-00-00 V1.0
Package Contents
Installing Procedures
1. Screw the Back Plate on the wall.
Making a hole that is able to let the AC wires and Ethernet cable pass
through. Hence, connect with the Door phone unit after screwing the
Back Plate on the wall. If necessary, Please connect the Earth wire to
the screw as Figure below.
Please be noted to reserve the space for junction wiring in the
wall as left diagram!
Screw the Back Plate on the wall
2. Connect the AC (Universal 110~240VAC) wires and Ethernet cable.
Plug the AC cable connector of DP101/R to Power-Connecting connector, and connect Ethernet cable to
DP101/R as Figure below. Be careful when you are connecting the AC wires, please check the AC condition
and turn off the general power switch before you start to connect the wires.
3. Screw the Video Door Phone with Back Plate.
After connecting the wires and cables properly, then screw the 4 screws and water stopper that come with
the package into the front panel, put back front cover
again, then you may power on the general power switch to start the configuration procedures.
Note: To fasten the Video Door Phone with the back plate properly to improve the waterproof function.
Screw the Video Door Phone with Back Plate wall
Using Video Door Phone & RFID Card Reader (Optional)
Making Calls on Video Door Phone
Using the Video Door Phone is quite simple. You will see "Door
bell" on the front
side.
Press "Door Bell" to make a call.
If there is no one answering this call, the bell sounds
(Ding-Dong) will continuously ring and the call will be
disconnected automatically after 15 seconds. (The time out
can be set at Web for 15, 30, 45 and 60 seconds).
Answering Calls on IP Video Phone/Video Indoor Station
To answer the call from Video Door Phone on IP Video Phone is
same as normal call. You may answer with following ways:
Press the SPEAKER
button.
Press "Answer" soft-function key.
Pick up the handset/ Press the button.
DP101R RFID Card Usage
Residents scan RFID card on the reader. DP101R will verify the
database to determine whether to open Electric-Door-Lock or
not.
Issue Master RFID Card First Time
For the first time, after the installation of DP101R is
completed, take the Master RFID Card from package contents
to scan on the DP101R RFID reader. This Master RFID card will
be used as Master Card1.
Upgrade new cards with Master Card:
Scan Master Card on DP101R First.
Then Scan New RFID Card on DP101R, DP101R will store New
ID into Database.
.
Please double check all the installation procedures
Door Bell
RFID Card Usage