Bosch 2 Originele handleiding - Pagina 19

Pagina afdrukken

1. Starting Operation

OBJ_BUCH-412-001.book Page 38 Thursday, April 3, 2008 3:18 PM

38 | English

or to adjust the worklight. Adjust the worklight

to the desired position first (see "Adjusting the

LED Worklight", page 38) before adjusting the

angled drive head.

Loosen the lock nut 20 by inserting an appropri-

ate tool into an opening of the lock nut and turn-

ing the lock nut in the direction of the arrow a

(left thread).

Unscrew the angled drive head 3 in arrow direc-

tion b until it can be removed. Unscrew the lock

nut 20 from the motor housing 33 in arrow di-

rection a.

Now, the marking ring can be exchanged or the

worklight can be adjusted.

– Turn the lock nut 20 in arrow direction c onto

the motor housing 33 and screw on the an-

gled screw head again turning in arrow direc-

tion b.

– Lock the angle nutrunner head by screwing

the lock nut 20 in arrow direction c.

– Retighten lock nut 20 again with a tightening

torque of approx. 50 Nm.

Adjusting the LED Worklight (see figure L)

ANGLE EXACT 25 – 250 | 30 – 380 | 40 – 280 |

50 – 210

For these industrial cordless angle wrenches,

the angled screw head must be removed first,

see "Adjusting and Removing the Angled Drive

Head", page 37. Adjust the worklight as de-

scribed below.

ANGLE EXACT 2 | 3 | 6 | 7 | 7 – 900 | 8 |

10 – 650 | 14 – 420 | 14CF | 15 |

17 | 22CF | 23 | 29CF | 30

Press off the marking ring 17 with a thin screw-

driver blade, a knife, or similar. Using snap-ring

pliers, slide the snap ring 34 toward the rear onto

the housing shell. The two shell halves of the LED

holder 16, which enclose the LED worklight 18,

can now be adjusted to any requested position.

Pay attention not to damage the cable of the LED

worklight 35 and slide it into the cavity intended

for it in the housing shell without kinking. En-

close the LED worklight 18 again with the two

housing shells of the LED holder 16. Press the

snap ring 34 and the marking ring 17 back to

their initial positions.

3 609 929 B34 | (3.4.08)

Maintenance and Service

Maintenance and Cleaning

Before any work on the machine (e.g., main-

tenance, tool change, etc.) as well as during

transport and storage, set the rotational di-

rection switch to the centre position. Unin-

tentional actuation of the On/Off switch can

lead to injuries.

For safe and proper working, always keep

the machine and ventilation slots clean.

When the battery is no longer operative, please

refer to an authorised after-sales service agent

for Bosch power tools.

If the machine should fail despite the care taken

in manufacturing and testing procedures, repair

should be carried out by an after-sales service

centre for Bosch power tools.

In all correspondence and spare parts order,

please always include the 10-digit article

number given on the type plate of the machine.

Power Tool Lubrication

Lubricants:

Special gearbox grease (225 ml)

Article number 3 605 430 009

Molycote grease

SAE 10/SAE 20 engine oil

Clean the gearbox after the first 150 running

hours using a mild solvent. Follow the solvent

manufacturers directions for use and disposal.

Lubricate the gearbox using Bosch gearbox

lube. Repeat the lubrication procedure every

300 hours after the initial gearbox service.

Oil the moving parts of the shut-off clutch after

100000 screwing operations with a few drops of

SAE 10/SAE 20 motor oil. Lubricate the sliding

and rolling parts with Molycote grease. At this

time, inspect the clutch for wear in order to en-

sure that the repeatability and accuracy have

not been affected. Afterwards, the torque of the

clutch must be readjusted.

Have maintenance and repair work per-

formed only by qualified specialists. In this

manner, it can be ensured that the safety of

the power tool is maintained.

Bosch Power Tools