Bosch 800 Series Installatiehandleiding - Pagina 10

Blader online of download pdf Installatiehandleiding voor {categorie_naam} Bosch 800 Series. Bosch 800 Series 32 pagina's. Built-in wall ovens
Ook voor Bosch 800 Series: Handleiding voor installatie-instructies (24 pagina's), Installatiehandleiding (40 pagina's), Gebruiks- en onderhoudshandleiding (12 pagina's), Installatiehandleiding (23 pagina's), Installatiehandleiding (28 pagina's), Installatiehandleiding (32 pagina's), Gebruiksaanwijzing (32 pagina's), Installatiehandleiding (32 pagina's), Snelstart- en veiligheidshandleiding (7 pagina's), Gebruiks- en onderhoudshandleiding (40 pagina's), Installatiehandleiding (40 pagina's), Installatiehandleiding (32 pagina's), Handleiding voor installatie-instructies (40 pagina's), Installatiehandleiding (48 pagina's), Gebruiks- en onderhoudshandleiding (33 pagina's), Gebruiks- en onderhoudshandleiding (49 pagina's), Snelstarthandleiding (7 pagina's), Snelstart- en veiligheidshandleiding (13 pagina's), Servicehandleiding (36 pagina's), Handleiding voor installatie-instructies (29 pagina's), Gebruiks- en onderhoudshandleiding (24 pagina's), Gebruiks- en onderhoudshandleiding (40 pagina's), Handleiding voor installatie-instructies (28 pagina's)

Pagina afdrukken
Bosch 800 Series Installatiehandleiding

Attaching the mounting plate to the wall

Preparing rear wall
CAUTION
9
Wear gloves to avoid cutting fingers on sharp
edges.
Note: Make sure the cabinet bottom is level.
Draw a vertical line on the wall at the center of the
1.
cabinet space.
Cabinet with front overhang: Draw a line on the back
2.
wall equal to the depth of the front overhang.
Tape the REAR WALL TEMPLATE onto the wall
3.
matching the centerline and touching the bottom of the
cabinet or the level line.
Draw a horizontal line on the wall at the bottom of the
4.
Rear Wall Template.
Drill holes at locations A and B:
5.
3/16" (5 mm) holes for wood screws (stud)
▯
5/8" (16 mm) holes for toggle bolts (no stud)
▯
Note: If neither A nor B is in a stud, find a stud
somewhere in the area of the mounting plate and drill
a 3/16" (5 mm) hole.
It is important to use at least one wood screw mounted
firmly in a stud to support the weight of the microwave.
Wall venting installation only: Cut out the shaded
6.
area "F" on the REAR WALL TEMPLATE using a saber
or keyhole saw.
CAUTION
9
If exhaust adaptor is positioned outside consider
recommended dimensions, otherwise grease-
laden air will discharge into house structure.
Remove REAR WALL TEMPLATE.
7.
Attaching the mounting plate
Remove the toggle wings from the bolts.
1.
Insert the bolts into the mounting plate through the
2.
holes designated to go into drywall.
10
Attach toggle wings from the back of the mounting
3.
plate onto each bolt. Leave enough space for toggle
wings to go through the wall and to open.
Place the mounting plate against the wall and push the
4.
bolts through the drywall.
Finger tighten the bolts to make sure toggle wings
5.
have opened against drywall.
Verify that the plate is properly centered and level.
6.
Securely tighten all screws, including the wood screw.
7.