Bosch SGE63E06UC/44 Handleiding voor installatie-instructies - Pagina 3
Blader online of download pdf Handleiding voor installatie-instructies voor {categorie_naam} Bosch SGE63E06UC/44. Bosch SGE63E06UC/44 37 pagina's.
Pagina afdrukken
Avoiding
General
Hazards
Do
not
use the
dishwasher
untiJ it is compJeteJy
installed.
When
opening
the door
on an uninstalled
dishwasher,
carefully
open the door while supporting
the rear of the unit. Failure to follow
this warning
can
cause the dishwasher
to tip over and result in serious
injury.
Before
installing
the
"L"-shaped
supplied
counter-
top mounting
brackets
(select models),
decide
which
method
will be used to secure the dishwasher
into its
opening.
Once these mounting
brackets
are installed
on the dishwasher,
removing
them
is difficult
and will
damage
the mounting
brackets
and the dishwasher.
In some
conditions,
hydrogen
gas
can form
in a
hot water system
that has not been used for weeks.
Hydrogen
gas is explosive.
Before
filling
a dishwasher
from
a system
that
has
been off for weeks, run the water from a nearby faucet
in a well ventilated
area until there is no sound or evi-
dence of gas.
Temperatures
required
for soldering
and sweating
will
damage
the dishwasher's
base and water inlet valve.
If plumbing
lines are to be soldered
or sweated,
keep
the heat source at least 6 inches (152.4 ram) away from
the dishwasher's
base and water inlet valve.
Removing
any cover or pulling the dishwasher
from the
cabinet
can expose
hot water connections,
electrical
power
and sharp edges or points.
Handle with care.
The customer
has the responsibility
of ensuring
that the
dishwasher
electrical
installation
is in compliance
with
all national
and local electrical
codes and ordinances.
The dishwasher
is designed
for an electrical
supply
of
120V, 60 Hz, AC,
connected
to
a dishwasher-
dedicated,
properly
grounded
electrical
circuit
with
a fuse or breaker
rated for 15 amps. Electrical
supply
conductors
shall be a minimum
#14 AWG copper
only
wire rated at 75°C (167°F) or higher.
This appliance
must
be connected
to a grounded
metal,
permanent
wiring
system,
or an equipment-
grounding
conductor
must
be run with
the
circuit
conductors
and
connected
to
the
equipment-
grounding
terminal
or lead on the appliance.
Do not
use extension
cords.
Improper
connection
of
the
equipment-grounding
conductor
can result in a risk of electric
shock. Check
with a qualified
electrician
or service
representative
if you are in doubt
whether
the appliance
is properly
grounded.
Do not modify
the plug provided
with the
appliance,
if it will not fit the outlet,
have a proper
outlet
installed
by a qualified
electrician.
A
Avoiding
Plumbing/Scalding
Hazards
Do not perform
any work
on a charged
hot water
line.
Serious
injury
could
result.
Only
qualified
plumbershould
perform
plumbing
work.
Do
not
attempt
any work on the dishwasher
hot water supply
plumbing
until you are certain the hot water supply is
shut off.
Avoiding
Electrical
Shock/Fire
Hazards
Do not allow the electrical
and water supply
lines to
touch. Separate
channels are provided
under the dish-
washer.
Do not work on an energized
circuit.
Doing so could
result in serious injury or death. Only qualified
electri-
cians should
perform
electrical
work. Do not attempt
any work on the dishwasher
electric
supply circuit
until you are certain the circuit is de-energized.
Do not over tighten
the 90 ° elbow.
Doing
so may
damage
the water inlet valve and cause a water leak.
Temperatures
required
for
soldering
and
sweating
will
damage
the
dishwasher's
water
inlet
valve.
If
plumbing
lines are to be soldered
or sweated,
keep
the heat source at least 6 inches (152.4 ram) away from
the dishwasher's
water inlet valve.
Check
local plumbing
codes for approved
plumbing
procedures
and accessories.
All plumbing
should
be
done in accordance
with national
and local codes.
Make sure electrical
work is properly
installed.
There
should
be no loose electrical
connections.
Ensure all
electrical
connections
are properly
made.
These instructions
depict
an installation
method
for
stainless
steel braided
hose or PEX hot water supply
lines.
If using
copper
tubing
or other
material
for
water supply, defer
to a licensed
plumber
for proper
installation.