AirStage ARUL12RLAV Installatiehandleiding - Pagina 20
Blader online of download pdf Installatiehandleiding voor {categorie_naam} AirStage ARUL12RLAV. AirStage ARUL12RLAV 20 pagina's. Indoor unit (duct type)
Ook voor AirStage ARUL12RLAV: Bedieningshandleiding (8 pagina's)
Pagina afdrukken
00
Auto restart
40
01
00
External
46
01
control
02
00
Error report
47
target
01
8. TEST RUN
8.1. Test run using PCB (Outdoor unit)
• Refer to the Installation Manual for the outdoor unit if the PCB for the outdoor unit is to
be used for the test run.
8.2. Test run using Remote Controller
• Refer to the Installation Manual for the remote controller to perform the test run using
the wireless remote controller.
• When the air conditioner is being test run, the OPERATION and TIMER indicators
fl ash slowly at the same time.
9. CHECK LIST
Pay special attention to the check items below when installing the indoor unit(s). After
installation is complete, be sure to check the following check items again.
CHECK ITEMS
Has the indoor unit been installed
correctly?
Has there been a check for gas
leaks (refrigerant pipes)?
Has heat insulation work been
completed?
Does water drain easily from the
indoor units?
Is the voltage of the power source
the same as that indicated on the
label on the indoor unit?
Are the wires and pipes all
connected completely?
Is the indoor unit earthed (grounded)? Short circuit
Is the connection cable the
specified thickness?
Are the inlets and outlets free of any
obstacles?
Does start and stop air conditioner
operation by remote controller or
external device?
After installation is completed, has
the proper operation and handling
been explained to the user?
En-19
Enable or disable automatic
system restart after a power
outage.
Enable
* Auto restart is an emergency
function such as for power
failure etc.
Do not start and stop the
indoor unit by this function in
normal operation.
○
Disable
Be sure to operate by the
control unit, converter or
external input device.
Allow an external controller to
○
start or stop the system, or to
Start/Stop
perform an emergency stop.
* If an emergency stop is
performed from an external
Emergency
controller, all refrigerant
stop
systems will be disabled.
* If forced stop is set, indoor
unit stops by the input to
the external input terminals,
Forced stop
and Start/Stop by a remote
controller is restricted.
○
All
Change the target for reporting
errors. Errors can either be
Display only
reported in all locations, or
on central
only on the central remote
remote con-
controller.
troller
If not performed correctly
Vibration, noise, indoor unit may
drop
No cooling, No heating
Water leakage
Water leakage
No operation, heat or burn damage
No operation, heat or burn damage
No operation, heat or burn damage
No cooling, No heating
No operation
10. ERROR CODES
If you use a wired type remote controller, error codes will appear on the remote control-
ler display. If you use a wireless remote controller, the lamp on the photodetector unit
will output error codes by way of blinking patterns. See the lamp blinking patterns and
error codes in the table below.
Error display
OPERATION
lamp (green)
(orange)
(1)
(1)
(1)
(3)
(3)
(4)
(4)
(5)
(5)
(9)
Display mode
( ) : Number of fl ashing
Wired Remote Controller Display
CHECK
BOX
For details on marking the ERROR CODES, please refer to the Manual of "IR Receiver
Unit" or "Wired Remote Controller".
Wired Remote
TIMER
Controller Error
FILTER
lamp
code
lamp (red)
(2)
(4)
(6)
(1)
(2)
(1)
(2)
(1)
(3)
(15)
: 0.5s ON / 0.5s OFF
: 0.1s ON / 0.1s OFF
Error code
Error contents
Remote controller
communication error
Anomalous network
communications
Parallel
communication error
Power frequency error
Model information
error/EEPROM
accession error
Room temperature
thermistor error
Indoor heat exchanger
temperature
thermistor error
Indoor fan motor error
Drainage error
Outdoor unit error