AirStage ARXD014GLEH Installatiehandleiding - Pagina 17

Blader online of download pdf Installatiehandleiding voor {categorie_naam} AirStage ARXD014GLEH. AirStage ARXD014GLEH 18 pagina's. Indoor unit (duct type)

Pagina afdrukken

AirStage ARXD014GLEH Installatiehandleiding

7.5. Switching of airflow direction louver function

When auto louver grille (Optional parts) is attached, set the airﬂ ow direction louver func-

tion "Valid".

The airﬂ ow direction louver of auto louver grille can be operated by the remote controller

while the airﬂ ow direction louver function is valid.

•

Installation method

Set the DIP switch SET 4 SW2, SW2 referring to the Table D.

Dip switch "SET 4"

OFF

Table D

Airflow direction louver function "Invalid"

OFF

DIP switch

(Factory setting)

SET 4 SW2

Airflow direction louver function "Valid"

7.6. Function setting

• FUNCTION SETTING can be performed with the wired or wireless remote controller.

(The remote controller is optional equipment)

• Refer to the wired or wireless remote controller manual for detailed setting information.

• Refer to "7.1. Setting the address" for indoor unit address and refrigerant circuit address

settings.

• Turn the power of the indoor unit ON before starting the setting.

* Turning on the power to the indoor units initializes EEV, so make sure the piping air tight

test and vacuuming have been conducted before turning on the power.

* Also check again to make sure no wiring mistakes were made before turning on the

power.

Function details

Function

Setting number

number

00 Standard

Filter indica-

01 Longer

tor interval

02 Shorter

00 Enable

01 Disable

Filter indica-

Display only on

tor action

central remote

controller

(Forbidden)

Static pres-

Refer to "7.3. Static pressure mode"

sure

(Forbidden)

00 Standard

Cool air

01 Adjust (1)

temperature

trigger

02 Adjust (2)

00 Standard

01 Adjust (1)

Heat air

02 Adjust (2)

temperature

trigger

03 Adjust (3)

00 Enable

Auto restart

01 Disable

00 Super low

Follow the

Cool Air

setting on

Prevention

the remote

controller

00 Start/Stop

Emergency

stop

External

control

02 Forced stop

00 All

Error report

Display only on

target

central remote

controller

Follow the

Fan set-

setting on

ting when

the remote

cooling

controller

thermostat

OFF

01 Stop

IU AD

REF AD

RC AD

×10

×1

×10

×1

SET3

SET4

Default

Details

Adjust the filter cleaning interval noti-

fication. If the notification is too early,

change to setting 01. If the notifica-

tion is too late, change to setting 02.

Enable or disable the filter indicator.

Setting 02 is for use with a central

remote controller.

Adjust the cool air trigger tempera-

ture. To lower the trigger tem-

perature, use setting 01. To raise the

trigger temperature, use setting 02.

Adjust the heat air trigger tempera-

ture. To lower the trigger temperature

by 6 degrees C, use setting 01. To

lower the trigger temperature by 4

degrees C, use setting 02. To raise

the trigger temperature, use setting

03.

Enable or disable automatic system

restart after a power outage.

Restrain the cold airflow with making

the airflow lower when starting heat-

ing operation. To correspond to the

ventilation, set to 01.

Allow an external controller to start

or stop the system, or to perform an

emergency stop.

* If an emergency stop is performed

from an external controller, all re-

frigerant systems will be disabled.

* If forced stop is set, indoor unit

stops by the input to the external

input terminals, and Start/Stop by a

remote controller is restricted.

Change the target for reporting

errors. Errors can either be reported

in all locations, or only on the central

remote controller.

When set to 01, the fan stops when

the thermostat is OFF in cooling

operation. Connection of the wired

remote controller (2-wire type or

3-wire type) and switching its therm-

istor are necessary.

Function

Setting number

number

Forced ther-

mostat off

Switching

function for

(Forbidden)

external

inputs

Refrigerant

leak detection

(Forbidden)

Single

setpoint auto

Auto mode

mode

type

(traditional)

Dual setpoint

auto mode

00 0°C

01 0.5°C

02 1.0°C

03 1.5°C

Deadband

04 2.0°C

value

05 2.5°C

06 3.0°C

07 3.5°C

08 4.0°C

09 4.5°C

(Forbidden)

8. TEST RUN

8.1. Test run using Outdoor unit (PCB)

• Refer to the Installation Manual for the outdoor unit if the PCB for the outdoor unit is to

be used for the test run.

8.2. Test run using Remote Controller

• Refer to the Installation Manual for the remote controller to perform the test run using the

wireless remote controller.

• When the air conditioner is being test run, the OPERATION and TIMER indicators flash

slowly at the same time.

9. CHECK LIST

Pay special attention to the check items below when installing the indoor unit(s). After

installation is complete, be sure to check the following check items again.

CHECK ITEMS

Has the indoor unit been installed correctly?

Has there been a check for gas leaks (refriger-

ant pipes)?

Has heat insulation work been completed?

Does water drain easily from the indoor units? Water leakage

Is the voltage of the power source the same as

that indicated on the label on the indoor unit?

Are the wires and pipes all connected com-

pletely?

Is the indoor unit earthed (grounded)?

Is the connection cable the specified thick-

ness?

Are the inlets and outlets free of any ob-

stacles?

Does start and stop air conditioner operation

by remote controller or external device?

After installation is completed, has the proper

operation and handling been explained to the

user?

Default

Details

Setting is required when connecting

a refrigerant-leak detecting device.

(only for J-IIIL series)

Switch the setting method of

auto mode to single or dual

(cooling/heating).

For heat pump systems, it is

necessary to set the master indoor

unit (by wired remote controller).

Choose the minimum temperature

between cooling and heating

settings (deadband) for Dual

setpoint auto mode (set in No. 68).

CHECK

If not performed correctly

Vibration, noise, indoor unit

may drop

No cooling, No heating

Water leakage

No operation, heat or burn

damage

No operation, heat or burn

damage

Short circuit

No operation, heat or burn

damage

No cooling, No heating

No operation

BOX

En-16