Bosch Vision 300 Series SHX43R52UC Aan de slag handleiding
Blader online of download pdf Aan de slag handleiding voor {categorie_naam} Bosch Vision 300 Series SHX43R52UC. Bosch Vision 300 Series SHX43R52UC 2 pagina's. Short instructions
Getting started with your new dishwasher.
1
Adding Rinse Aid
— Rinse aid is necessary to improve drying results.
— Add rinse aid when the Rinse Aid LED or symbol
on the control panel illuminates.
— Lift the tab to open the rinse aid reservoir and
add liquid rinse aid by pouring over the arrow.
— Wipe up any excess rinse aid that may puddle.
2
Adjust Amount of Rinse Aid Dispensed
— Turn the arrow inside the rinse aid dispenser to
adjust the amount of rinse aid dispensed.
To decrease
streaks on glass
For up to 45% dryer dishes:
1 - Always use Rinse Aid
2 - Use Auto Cycle
3 - Press Sanitize button
The sanitize feature is available only in the Heavy, Auto, Normal
and Half Load cycles. Press the "Sanitize" button to activate the
sanitation features during the Auto, Normal and Half Load cycles.
The sanitize LED or symbol
ments are met.
Frequently Asked Questions
Dishwasher beeping after cycle end: The default settings alert
the consumer that the cycle has finished. To adjust the volume
or deactivate, refer to "Operating the Dishwasher" in the Use
and Care Manual.
Dishes are not drying properly: Refer to section above.
Odor: Debris at the bottom of the dishwasher or in the door
seal can cause odor. Clean both according to instructions in the
Use and Care Manual.
Dishwasher still on after cycle ends: Default factory settings
have the dishwasher stay powered on after a cycle ends.
Customer must manually turn the dishwasher off. Dishwasher
must be powered on again in order to start a new cycle.
9000633150 Rev A 3/11
3
— Use fresh powdered detergent or detergent tabs
for best results.
— 1 tablespoon will clean most loads
— 3 tablespoon max, do not overfill
— When using detergent tabs, lay them flat to avoid
contact with the cover.
To close the cover:
— Place finger on arrow and slide
cover fully left.
— Push rear end of cover down
firmly until it clicks.
To open the cover:
— Push the blue button inward
(not down) and cover will slide
open.
4
— Open the door and press the On/Off button to turn dishwasher on.
— Select a cycle and desired option if applicable.
— Close the door to begin the cycle.
To decrease
Cancelling a cycle / Reset the dishwasher
spots on glass
If you need to cancel a cycle or the dishwasher control panel seems to not respond,
cancel or reset by following these steps.
— Open the door slightly and press and
hold the two Cancel/Reset buttons
for 3 seconds.
— Close the door and wait about 1 min-
ute while the dishwasher drains.
will light when sanitation require-
Adding Detergent
To Start the Dishwasher
Cycle Descriptions
Heavy: Uses higher water temperature and pressure to remove
baked-on foods
Auto: Reads the size and soil of each load, adjusting water and
heat to the ideal balance for optimum cleaning results
Normal: Cleans normal loads with loosely attached, normal soiling
Express*: Cleans lightly soiled loads with reduced wash time
Half Load*: Can reduce energy and water consumption
when washing small loads that fill approximately half of the
dishwasher's capacity
* Available wash cycles vary by model
To Contact Customer Service
Call the toll free Customer Service number, 1-800-944-2904.
Before calling, locate the model number and serial number on the
label on the inside of the dishwasher door.
ALWAYS READ YOUR USE AND CARE MANUAL FOR DETAILED
INSTRUCTIONS AND IMPORTANT SAFETY NOTICES.
To close the cover
To open the cover
2
— Open the door and press the On/Off
button. If you choose to start a new
cycle, turn the unit on again and select
a cycle.
Cancel/Reset
3 Tbsp. maximum
2 Tbsp. (25ml)
1 Tbsp. (15ml)