Draper Access/Series M Installatie- en bedieningsinstructies
Blader online of download pdf Installatie- en bedieningsinstructies voor {categorie_naam} Draper Access/Series M. Draper Access/Series M 2 pagina's. Draper access/series m projection screen
Pagina afdrukken
Access/Series M Projection Screen by Draper
➀ Read instructions through completely before proceeding.
➁ Follow instructions carefully. Installation contrary to instructions
invalidates warranty.
➂ Entire bottom of screen case should be unobstructed to permit access
to bottom panel for servicing.
➃ Screen should be installed level (using a carpenter's level).
➄ Nothing should be fastened to screen dowel or viewing surface.
NOTE: Screen has been thoroughly inspected and tested at factory and
found to be operating properly prior to shipment.
Hanging Screen
When locating viewing surface and checking clear ance for screen operation,
remember surface is centered in the length of the case. Regardless of
mounting method used, the following points apply:
➀ Mounting brackets are shipped attached to the case. Engage each bracket
with top of housing as shown below and tighten set screws. A bracket
should be within 18" of each end of screen case. Brack ets can be removed
and case mounted with lag screws through top of case (holes drilled on
site).
➁ Screen should be positively and securely supported so that vibration or
even abusive pulling on viewing surface will not weaken installation.
➂ Installer must insure that fasteners used are of adequate strength and
suitable for the mounting surface chosen. Supporting hardware (chains,
cables,
3
/
" rods, etc.) must be essentially vertical.
8
➃ Entire bottom of case must be readily accessible after in stal la tion is
complete.
➄ Front, back and top of case must be straight—not forced to warp or bow.
➅ If case is painted on location, removal of roller/fabric assembly is
recommended prior to painting. If not removed, slot on bottom of case
should be shield ed to protect view ing surface from paint splatters or
overspray.
Typical
Installation
Alternate
Installation
(additional
set of
brackets
required
but not
included)
Bottom Access Panel Installation/Removal
Bottom access panel hooks over the lower inside edge of the screen housing
and then is pivoted downward until the engagement brackets on each end of
the bottom panel click into place with the ball detents on each endcap. Make
sure bottom access panel clicks in place at each end of its length.
®
Copyright © 2009 Draper Inc. Form AccessM_Inst09
Installation/Operating Instructions
Caution
Slots along
top of case
permit
brackets to
be set at an
angle
Printed in U.S.A.
With bottom access panel
angled up approx. 20 degrees,
engage hook on the panel
with lip of the housing
Remove bottom access panel by pushing up at each corner of panel adjacent
to slot in bottom of the housing.
With bottom access panel angled up approximately at 20° it can be lifted off of
the lip of the housing and then lowered out of the housing completely.
Spring Roller/Fabric Installation
The bottom access panel must be removed fi rst.
The spear end mounting bracket has rectangular openings for accepting roller
spear. Back out the four set screws in bracket until they are fl ush with top side
of bracket.
To engage the spear end bracket fl ange above the two channels in the top of
the screen housing, rotate the bracket approximately 45° counterclockwise
to allow the top surface of the motor bracket to rest fl at against the top
inside of the housing. Rotating the bracket clockwise until it is engaged with
the channels, slide it along the length of the housing toward the left end of
housing, leaving approximately
Tighten the four set screws on the bracket fl ange using
Engage the idler end bracket (nylon bushing) in the same manner as the
spear end bracket and slide it toward the opposite end of the screen housing.
Do not tighten the set screws on this bracket until the roller/fabric assembly is
installed.
Locate the roller/fabric assembly and remove the retaining clip and fl at washer
from the idler end pin, and remove retaining clip from the spear. Remove
brackets from roller.
NOTE: This may require two people to perform safely. Raise the roller/
fabric assembly up into the screen housing and engage the spear of the roller
completely into the spear mounting bracket.
3
If roller is 1
/
" diameter, there will be an arrow imprinted on the spring end
4
of the roller. This arrow must be pointing UP, and you must use the slot
closest to the edge of the bracket.
1
If roller is 2
/
" or 3" diameter, there will be a notch cut out on the spring
4
end of the roller. This notch must be pointing DOWN, and you must use the
appropriate slot.
If you encounter any diffi culties installing or servicing your Access/Series M screen, call
your dealer or Draper, Inc., in Spiceland, Indiana, (765) 987-7999 or fax (765) 987-7142.
Using the hook and lip as a pivot,
pull the panel downward until the
engagement brackets click into
place with the ball detent
on each endcap
Engagement bracket
(one on each end of the
bottom access panel)
Bottom flange of Access housing
Bottom access panel pushup
points for panel removal
Caution: Beware of pinch
points at ends of closure
Access case as seen from below
3
/
" clearance between bracket and endcap.
4
(Continued on page 2)
1
/
" hex key.
8