Draper Paragon Installatie- en bedieningsinstructies - Pagina 2
Blader online of download pdf Installatie- en bedieningsinstructies voor {categorie_naam} Draper Paragon. Draper Paragon 2 pagina's. 220v electric screen
Ook voor Draper Paragon: Specificaties (2 pagina's), Installatie- en bedieningsinstructies (2 pagina's), Installatie- en bedieningsinstructies (2 pagina's)
Pagina afdrukken
Paragon by Draper
Optional Wall Mounting Bracket
1"
1
3
/
"
4
1
3
/
"
4
1
/
" dia.
2
3
/
8
Bottom Closure Removal/Replacement
Removal and replacement of the bottom closure panel
requires two people positioned about 5' from each end of
the panel. Closure should be handled as shown in Step 5
below to prevent bowing of the closure during handling.
Before removing bottom
closure, you must fi rst
remove screws at each
end of case (see drawing
at right).
Screw and washer
Step 1
Step 2
Step 3
Step 4
Case Dimensions*
7
2
/
"
8
7
2
/
"
8
1
13
/
"
4
7
2
/
"
2¼"
8
2"
" dia.
Step 5
See separate
Serial Commu-
nication-RS232
Instruction sheet
for enabling RS232
with the MC1.
www.draperinc.com
*
8"
2"
3
12"
1
/
"
8
2¼"
5"
2"
*Please Note: Optional wall brackets add 1¾" per bracket to case
length. Wall mounting bracket hole location is 1" from end of case.
Wiring Diagrams
Single Station Control
Internal Screen Wiring
White (Common)
Black (Down)
Red (Up)
Green (Ground)
Dashed wiring
by electrician
Single gang box by others
Control
Min. 4" x 2
1
/
" x 1
8
switch
Blue
Red
Black
Location of key
operated on-off
switch if furnished
To 110-120V Line
Low Voltage & Wireless Control
Two-Way Serial Communication (RS232) with MC1
Program LED
Fuse
MC1
(765) 987-7999
* - Case support brackets will be evenly spaced along the case
Multiple Station Control
Internal Screen Wiring
White (Common)
Black (Down)
Red (Up)
Green (Ground)
Cap off with wire
nut and tape
Red
Blue
7
/
" deep
8
Black
Red
Blue
Black
Red
Blue
Single gang box by others
Black
Min. 4" x 2
3 shown. More or less equally
feasible.
Location of key
operated on-off
switch if furnished
To 110-120V Line
White-Common to screen & 110-120V AC Neutral
Red-to screen (directional)
Brown-to screen (directional)
Yellow-to 110-120V AC-Hot
Black-to 110-120V AC-Hot
Green-Ground
Dashed wiring by electrician
Low voltage wiring by others
Eye Port for IR Eye, RF Receiver or LED
Wall Switch. For more than one of
these, a splitter is required.
3 Button Wall Switch
DOWN - Black
COM - White
UP - Red
Aux Port for connecting additional LVC-III
modules (up to six total can be linked-
connect from Aux to Eye).
To 110-120V Line
White-Common to screen & 110-120V AC Neutral
Red-to Screen (directional)
Brown-to Screen (directional)
Black-Hot to 110-120V AC
Green/Yellow-Ground
Low Voltage Wiring by others
AC Wiring by electrician
RS232 Data FROM Control System
RS232 Data TO Control System
Signal Ground & Manual Switch Common
Manual Switch Down
Manual Switch Up
Eye Port for IR Eye. For RF Receiver or LED
Wall Switch, a Splitter and a Power Supply
is required. Plug RF Receiver or LED Wall
Switch and Power Supply into splitter, then
run cable from Splitter to MC1 Eye Port.
Page 2 of 2
Dashed wiring
by electrician
1
7
/
" x 1
/
" deep.
8
8
Internal Screen Wiring
White (Common)
Red (Up)
Black (Down)
Green (Ground)
Location of key
operated on-off
switch if furnished
Internal Screen Wiring
White (Common)
Red (Up)
Black (Down)
Green (Ground)
Location of key
operated on-off
switch if furnished
To 110-120V Line