Premier by Draper
Types of Installation
Optional Ceiling Opening
Trim Kit (Dims-Side View)
8"
2
1
1
/
"
16
1
2
/
"
8
4"
3
6
/
"
4
ILT Limit Adjustment Continued from Page 1
➄ To set the viewing surface to an alternate format position, move the viewing
surface to the desired position and press the STOP button. Press and hold the
STOP button for at least three seconds to record the position.
Please Note: Pressing and releasing the UP button on the switch will move
the screen to its upper limit. Pressing and releasing
the DOWN button will move the screen to its lower
limit.
While the motor is in motion,
POSITION
pressing the STOP button for less
than two seconds will stop the
viewing surface at its present posi-
tion.
Once the motor is stopped,
pressing the STOP button will move the viewing
surface to its alternate format position.
Pressing and holding the STOP button, when the
motor is at rest or in motion, for at least three seconds
will record a new alternate format position.
Tab-Tension Adjustment
Procedure for Premier
➀ Determine which side requires adjustment.
➁ Secure dowel with one hand.
Caution: Do not touch or bend surface.
➂ Using Philips-head screwdriver,
depress spring-loaded adjustment screw
(see drawing) and slowly turn clockwise to
tighten tension, or counterclockwise to
loosen tension. The screw adjusts in
¼ turn increments. Adjust only one
increment (¼ turn).
➃ If problem is not corrected, leave screen in
position for 24 hours to allow surface
material to stretch into position.
➄ If problem still is not corrected, repeat steps 2 and 3.
Suspended
Appropriate hardware
provided by installer.
If using "S" Hooks )by others), be sure to crimp both
ends of the "S" Hooks.
1
/
"
16
P
O
T
S
U
D
p
o
w
n
FUNCTION
DOWN
Set LOWER limit
P
O
T
S
P
O
T
S
Set UPPER limit
UP
Normal Operation
CENTER
Slide
Switch
Back View
Tensioning
Cable
Dowel
Adjustment
Screw
www.draperinc.com
Wall
Appropriate hardware
13
provided by installer.
1
/
16
7
5
/
8
1"
15
/
16
Wiring Diagrams—110-120V Motor and Quiet Motor
Please Note: Do not wire motors in parallel.
Single Station Control
Internal Screen Wiring
White (Common)
Black (Down)
Red (Up)
Green (Ground)
Dashed wiring
by electrician
Control
Single gang box by others
switch
Min. 4" x 2
Blue
To Motor
with
Red
Black
Built-In
+
C
5V
o
Low Voltage
DC
m
m
o
n
Location of key
operated on-off
switch if furnished
To Motor
with
To 110-120V Line
Built-In
Low Voltage
Wiring Diagrams—110-120V Motor and Quiet Motor
with Built-in Low Voltage Controller
Single Low Voltage Control
Internal Screen Wiring
White (Neutral)
Black
Green (Ground)
Dashed wiring
Data Cable
by electrician
Wall Switch,
RF or IR
Receiver,
or integrated
control system
To 110-120V Line
(765) 987-7999
Case Dimensions
1
Mounting
5
/
"
4
hole
"
"
7
/
" dia.
8
electrical
connection
"
hole
2
1
/
8
Multiple Station Control
Red
1
7
/
" x 1
/
" deep
8
8
Black
Red
Black
Red
Black
Location of key
operated on-off
switch if furnished
To 110-120V Line
Multiple Low Voltage Controls
Dashed wiring
by electrician
To 110-120V Line
Page 2 of 2
"
Internal Screen Wiring
White (Common)
Black (Down)
Red (Up)
Green (Ground)
Cap off with wire
nut and tape
Blue
Dashed wiring
by electrician
Blue
Blue
Single gang box by others
1
7
Min. 4" x 2
/
" x 1
/
" deep.
8
8
3 shown. More or less equally
feasible.
Internal Screen Wiring
White (Neutral)
Black
Green (Ground)
Data
Cables
Wall Switches,
RF or IR
Receivers,
or integrated
control systems
Pagina afdrukken