Draper Targa TAR-29 Installatie- en bedieningsinstructies

Blader online of download pdf Installatie- en bedieningsinstructies voor {categorie_naam} Draper Targa TAR-29. Draper Targa TAR-29 4 pagina's. Electric projection screen

Pagina afdrukken

1 Read instructions through completely before proceeding.

2 Follow instructions carefully. Installation contrary to instructions invalidates

warranty.

3 Screen should be accessible for complete removal should fabric become

damaged or should other service be required.

4 Screen should be installed level (using a carpenter's level).

5 Nothing should be fastened to screen dowel or viewing surface.

6 Operating switch(es) packed separately in screen carton.

Do not discard with packing material.

7 Screen operates on 110-120V, 60 hz., 1.1 amp current draw.

NOTE: Screen has been thoroughly inspected and tested at factory and

found to be operating properly prior to shipment.

These instructions are meant as a guide only. They do not imply any

responsibility on the part of Draper, Inc. for improper installation or faulty

workmanship at the jobsite.

Hanging Screen

General:

When locating viewing surface and checking clearance for screen's operation,

remember surface is centered in case. Handle case carefully to protect its finish.

Regardless of mounting method, screen should be positively and securely sup-

ported so that vibration or even abusive pulling on the viewing surface will not

cause case to work loose or fall. Installer must insure that fasteners used are of

adequate strength and suitable for the mounting surface chosen.

Suspended Installation:

Suspend screens from holes in endcaps as shown. "S" hooks, chains (or cable)

and turnbuckles should be provided by installer. "S" hooks should go through

the front holes on the endcaps (see drawing on page 3), and both ends of the

"S" hooks should be crimped for additional safety. Chains should be attached to

beams or other structural members. Turnbuckles should be adjusted so screen

hangs level.

Wall Installation:

Mount screen through holes in back of endcaps as shown. Installer should

furnish screws, toggle bolts, molly bolts, nylon or lead anchors as required.

Wall Installation with 6" Extension Brackets:

Mount the brackets (not included with screen—see diagram on page 3) using

hardware recommended for "Wall Installation" (above). Then, suspend the

screen from the front holes with "S" hooks (as in "Suspended"). For added

safety, be sure to crimp both ends of the "S" hooks so the screen cannot

come off. For a more rigid installation, mount the screen from the back holes

to the front of the bracket by using the screws and nuts provided with the

brackets.

Wall or Ceiling Installation with Floating Brackets:

Floating brackets should be located on studs or joists. The bracket then

attaches at any almost any point along the case. For details, see separate

instruction sheet that ships with the Floating Wall Bracket.

Recessed Installation:

Recess should permit access for removal

of screen if necessary. Screen may be

mounted as in suspended or wall installation.

Optional Ceiling Opening Trim Kit available;

see diagrams at right and on page 3, and

separate instruction sheet (included with

Ceiling Opening Trim Kit).

The Ceiling Opening Trim Kit is for use in

an acoustical, drop ceiling only. Not recom-

mended for drywall or hard ceilings.

Form Targa_Inst15

Installation/Operating Instructions

Targa Electric Projection Screen by Draper

Caution

Floating Mounting Bracket

Ceiling Trim Kit

Screen Case

Back

Ceiling Tile

(By others)

Printed in U.S.A.

Electrical Connections

Screen operates on 110-120V, 60 hz., 1.1 amp current draw. Duty cycle: On 28

seconds/Off 4 minutes.

Junction box is located inside left endcap and cover plate is secured to endcap

with two screws which may be removed with a Torx-head or small straight-

blade screwdriver. Junction box contains red, black and white pigtail leads and

green internal ground wire, per wiring diagram on reverse.

Screen is shipped with internal wiring complete and control switch(es) fully

boxed. Wire connecting screen to switch(es) and switch(es) to power sup-

ply should be furnished by installer. Please Note: Screen must be installed in

accordance with the requirements of the Local Building Codes, the Canadian

Electrical Code (CEC), CAN/CSA C22.1 and the National Electric Code (NEC),

NFPA 70. An appropriate disconnect device shall be provided as part of the

building installation. Please Note: Do NOT wire motors in parallel.

All operating switches should be "off" before power is connected.

Plug-in power cord option available with built-in low voltage motor.

For Reconfiguration/Conversion of Non-detachable Power Cord to

Field Wiring for Models TAR-28, TAR-29 and TAR-30 Only:

1 Disconnect cord plug from outlet.

2 Remove junction box cover.

3 Disconnect wire nuts from black, white and green wires.

4 Remove power cord and strain relief from screen.

5 Connect the black motor wire to "hot" supply wire.

6 Connect white motor wire to "neutral" supply wire.

7 Connect green/yellow wire to "ground" supply wire.

8 Replace junction box cover.

Before operating screen remove tape securing fabric and dowel to roller. If view-

ing surface hangs out of case 8"-9", tape has probably been broken by rough han-

dling in shipment, allowing surface to "unwrap" one turn about the roller. Manually

wrap fabric back around the roller without turning the roller itself.

110-120V Single Station Control — 3-position up-off-down switch permits opera-

tion to be stopped at any point. Factory adjusted limit switches automatically stop

screen when fully down or fully up.

110-120V Multiple Station Control—Switches are similar in appearance to 110-

120V Single Station Control. Screen stops when switch is released and may be

restarted in either direction. Factory adjusted limit switches stop screen automati-

cally when fully down or fully up.

24V Control — Three-button up-stop-down switches stop at any point desired,

operate in any sequence. Factory adjusted limit switches automatically stop

screen when fully down or fully up.

Key Operated Switching — Two kinds of key-operated switches are optionally

available with this unit. 1 The key-operated power supply switch controls power to

the screen and switches. When it is "off", the switches will not operate screen. Key

may be removed from the switch in either "on" or "off" position. 2 A three-position

key switch permits the screen to be operated directly by key. In this case, the

screen's operator must always have a key.

RS232/Ethernet—Serial communication and network communication optionally

available with wall switches, RF or IR remote.

Plug & Play

—Provided with handheld IR remote control transmitter and

10' (3m) cord. No wiring necessary except to connect to RS232. Screen

is equipped with a handheld remote or 3-position operating switch. Three

positions (up-off-down) permit operation to be stopped at any point. Factory

adjusted limit switches automatically stop screen when fully down or fully up.

If you encounter any difficulties installing or servicing your Targa screen, call your

dealer or Draper Inc., Spiceland, Indiana, (765) 987-7999 or fax (765) 987-7142.

Operation

(Continued on next page)