Draper HG1601 Gebruiksaanwijzing - Pagina 4
Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Draper HG1601. Draper HG1601 13 pagina's. Hot air gun
Pagina afdrukken
WARNING
Please read the following instructions carefully, failure to do so could lead to serious personal
injury.
IMPORTANT
Draper Tools Limited recommends that this machine should not be modified or used for any
application other than that for which it was designed. If you are unsure of its relative applications
do not hesitate to contact us in writing and we will advise you.
1. KNOW YOUR MACHINE TOOL
Read and understand the owner's manual and labels affixed
to the tool. Learn its application and limitations as well as
the specific potential hazards peculiar to this tool.
2. KEEP GUARDS IN PLACE
and in working order.
3. REMOVE ADJUSTING KEYS AND WRENCHES
Form a habit of checking to see that keys and adjusting
wrenches are removed from tool before turning it on.
4. KEEP WORK AREA CLEAN
Cluttered areas and benches invite accidents. Floor must
not be slippery due to oil or sawdust.
5. AVOID DANGEROUS ENVIRONMENT
Do not use power tools in damp or wet locations or expose
them to rain. Keep work area well lit. Provide adequate
surrounding work space.
6. KEEP CHILDREN AWAY
All visitors should be kept a safe distance from work area.
7. MAKE WORKSHOP CHILDPROOF
- with padlocks, master switches, or by removing starter
keys.
8. DO NOT FORCE TOOL
It will do the job better and safer at the rate for which is
was designed.
9. USE RIGHT TOOL
Do not force tool or attachment to do a job for which is was
not designed.
10. WEAR PROPER CLOTHING
Do not wear loose clothing, gloves, neckties or jewellery
(rings, wristwatches) to catch in moving parts. NON SLIP
footwear is recommended.Wear protective hair covering to
contain long hair. Roll long sleeves above the elbow.
11. USE SAFETY GOGGLES (Head Protection)
Wear safety goggles (must comply with BS 2092) at all
times. Normal spectacles only have impact resistant lenses,
they are NOT safety glasses. Also, use face or dust mask if
cutting operation is dusty and ear protectors (plugs or
muffs) during extended periods of operation.
SAFETY WARNING
GENERAL SAFETY INSTRUCTIONS FOR MACHINE TOOLS
12. SECURE WORK
Use clamps or a vice to hold work. This frees both hands to
operate tool.
13. DO NOT OVERREACH
Keep proper footing and balance at all times.
14. MAINTAIN TOOLS WITH CARE
Keep tools sharp and clean for best and safest
performance. Follow instructions for lubricating and
changing accessories.
15. DISCONNECT POWER TO THE TOOLS
Before servicing, when changing accessories such as
cutters etc.
16. AVOID ACCIDENTAL STARTING
Make sure switch is in 'OFF' position before plugging in
cable to the power supply.
17. USE RECOMMENDED ACCESSORIES
Consult the owner's manual for recommended accessories.
Follow the instructions that accompany the accessories. The
use of improper accessories may cause hazards.
18. NEVER STAND ON TOOL
Serious injury could occur if the tool is tipped or if the
cutting tool is accidentally contacted. Do not store
materials above or near the tool such that it is necessary to
stand on the tool to reach them.
19. CHECK DAMAGED PARTS
Before further use of the tool, a guard or other part that is
damaged should be carefully checked to ensure that it will
operate properly and perform its intended function. Check
for alignment of moving parts, breakage of parts, mounting
and any other conditions that may affect its operation. A
guard or other part that is damaged should be properly
repaired or replaced.
20. DIRECTION OF FEED
Feed work into a blade or cutter against the direction of
rotation of the blade or cutter only.
21. NEVER LEAVE MACHINE RUNNING UNATTENDED
Turn power off. Do not leave machine until it comes to a
complete stop.
- 3 -