Draper LightBloc Zip Handleiding voor installatie-instructies - Pagina 3
Blader online of download pdf Handleiding voor installatie-instructies voor {categorie_naam} Draper LightBloc Zip. Draper LightBloc Zip 6 pagina's.
Ook voor Draper LightBloc Zip: Handleiding voor installatie-instructies (6 pagina's)
Pagina afdrukken
LightBloc Zip by Draper
Mounting Headbox - Zip 127 Angled Headbox
The LightBloc Zip 127 Angled Headbox can be mounted permanently to the
wall or ceiling (See Mounting Headbox - Permanently to Ceiling or Wall on
page 1); or the Headbox can rest atop the Side Channels and is held in place
there by two mounting studs coming down from the endcaps.
PLEASE NOTE:
Steps 1-5 of the Mounting Side Channels
section must be completed before mounting
the Zip 127 Angled Headbox. It is critical that
the full length of each Side Channel
is secured to the mounting surface.
1 Remove screws from bottom of Headbox,
remove Fascia and set aside. (See Fig. 11).
HEADBOX
MOUNTING
STUD
S i
d e
C h
a n
n e
l
3 Insert "Zippers" on the side of the Hem Bar into the fabric retainers in the
Side Channels (See Fig. 12).
4 Insert Headbox mounting stud into Side Channel (See Fig. 12).
5 Return Fabric Retainers to Side Channels and re-attach Covers.
The LightBloc Zip can also be installed in a pocket in the ceiling. You must
provide adequate clearance for removal of the Roller Assembly during
installation and maintenance.
The minimum depth of the ceiling pocket for the LightBloc Zip 92 is 4¾"
(120mm), and for the LightBloc Zip 127 is 6¼" (158mm). See Fig 13 below.
Zip 92
4 ¾"
(120mm)
3
/
"
5
(92mm)
8
7¼"
(
183mm)
Figure (11)
2 Insert "Zipper" on one side of
the Hem Bar into the fabric
retainer in the Side Channels
(See Fig. 12).
HEADBOX
MOUNTING
STUD
S i
d e
C h
a n
n e
Figure (12)
l
Pocket Installation
Zip 127
6¼" (
5" (
3
5
/
"
8
(92mm)
5
7
/
"
8
(148mm)
If the system is installed in a recess, it is unlikely that there will be sufficient
space above the side channels to allow the Headbox to be mounted onto them.
In these instances follow the steps for preparing the system (See Mount-
ing Headbox - Zip 127 Angled Headbox). Then mount the Headbox onto
Figure (11)
the side channels and present the entire system into the opening. Hold the
system in position and use appropriate screws to fix the side channels in
place. Apart from this, the other steps should be followed as described.
REMOVE
The LightBloc Zip operates on 110-120V, 60 Hz. current. Shade is shipped
FASCIA
with internal wiring complete and control switch (es) fully boxed, and supplied
with a 6' cable lead (standard). Longer lead can be substituted by removing
two screws in motor end of roller, removing lead, plugging new lead in, and
replacing screws. Wire to connect shade to switch (es) and switch (es) to
power supply should be furnished by installer. Connections should be made
in accordance with attached wiring diagram, and wiring should comply with
national and local electrical codes.
ZIPPER
DO NOT wire motors in parallel without written permission from Draper.
All operating switches should be "off" before power is connected.
HEMBAR
CAUTION: Be sure all switches are in "off" position before adjusting limit switches.
Always be prepared to shut off manually when new adjustment is being tested.
FABRIC
Do not allow the shade roller to become exposed by running the shade
RETAINER
fabric too far down. Shade may be severely damaged if allowed to run too far up
STRIP
or down. Each shade's limit switch must be set if using group control system.
1 Fully depress both limit switch push buttons, then operate wall switch to make
sure system works properly.
2 Raise shade to desired "up" stop position.
3 Set upper limit by depressing and releasing the proper (back) push button.
4 Lower shade to desired "down" stop position.
5 Set lower limit by depressing and releasing the proper (front) push button.
For instructions on setting limits on these motors, consult Draper's Motorized
Shade Handbook, available in the motorized shades section of www.draperinc.com.
The LightBloc Zip has optional Anti-Insect Brush
Seals pre-installed along the width of the fascia.
There are also brush seals supplied for each of
the side channels that will need to be installed.
Remove the double-sided tape and apply to the
158mm)
side channels as shown at right (Fig. 14).
127mm)
5"
(
127mm)
7¼"
(
183mm)
www.draperinc.com
(765) 987-7999
Alternate Mounting for Jamb Recessed
Installations (Zip 127 Angled Only)
Complete Electrical Connection
Limit Switch Adjustments—Standard Motor
Limit Switch Adjustments—RTS Motors
Attaching Anti-Insect Brush Seals (Optional)
Zip 92
4 ¾"
(120mm)
3
/
"
5
(92mm)
8
3
5
/
"
8
(92mm)
5
7
/
"
8
(148mm)
Page 3 of 6
Insect Barrier
Brush Seal
Figure (14)