Bosch Benchmark Series Handleiding voor installatie-instructies - Pagina 10
Blader online of download pdf Handleiding voor installatie-instructies voor {categorie_naam} Bosch Benchmark Series. Bosch Benchmark Series 40 pagina's. Built-in wall ovens
Ook voor Bosch Benchmark Series: Servicehandleiding (36 pagina's), Installatiehandleiding (32 pagina's), Snelle referentiehandleiding (4 pagina's), Servicehandleiding (45 pagina's), Snelstart- en veiligheidshandleiding (13 pagina's)
Pagina afdrukken
Round pipes
An inner diameter of Ø 8" (200 mm) is recommended.
Flat ducts
The inner cross-section must correspond to the diameter
of the round pipes.
Ø 8" (200 mm) approx. 50.3 inches
Flat ducts should have no sharp deflections.
▯
Use sealing strip for deviating pipe diameters.
▯
Installation Procedure
CAUTION
9
Ensure that there are no electric wires, gas or water
pipes in the area where holes are to be made.
Preparing the installation
Mark a vertical center line on the wall from the ceiling
1.
to the lower edge of the extractor hood.
Align the drill template on the center line and the
2.
bottom edge of the extractor hood and glue on.
Mark positions for the screws and the contour of the
3.
attachment area.
Mark holes for the flue's angle brackets. The center of
4.
the angle bracket is marked with a hole. Place the
angle brackets in the center of the center line, align
them horizontally and mark the positions of the holes.
Fitting the wall retainer
Drill holes with Ø 5/16" (7.9 mm) for the angle
1.
bracket.
Press in the wall plugs flush with the wall.
2.
Screw screws (5x34 mm) into the wall plugs by hand
3.
in order to spread the plugs apart.
Unscrew screws.
4.
Screw on the angle bracket for the flue duct.
5.
Making the ceiling breakthrough
Using a spirit level, extend the center line of the drill
1.
template to the ceiling.
Mark the ceiling breakthrough (Ø 8 1/2" (216 mm)) at
2.
least 4 5/8" (117 mm) away from the wall.
Making the wall breakthrough
Using a spirit level, extend the center line of the drill
1.
template to the ceiling.
Depending on the curved section of the wall
2.
breakthrough (Ø 8 1/2" (216 mm)) mark at least 26 1/
2" (660 mm) above the bottom edge of the extractor
hood.
10
(324 cm
)
2
2
Checking the wall
The wall must be level, vertical and adequately load-
▯
bearing.
The depth of the bore holes must be the same length
▯
as the screws. The wall plugs must have a secure grip.
The enclosed screws and wall plugs are suitable for
▯
solid brickwork. Suitable fasteners must be used for
other structures.
Mounting the extractor hood on the wall
WARNING
9
RISK OF INJURY
The appliance is heavy. To move the appliance, 2
people are required. Use only suitable tools and
equipment.
Initially remove the protective foil from the back of the
1.
appliance and, following installation, remove foil
completely.
Mark the upper holes on the wall.
2.
Note: Ensure that the holes are horizontal and aligned
centered on the center line.
Drill the upper holes. Maintain a distance of 1/4"
3.
(6 mm) between the wall and screw head.
Remove grease filter.
4.
Hang the extractor hood on the upper screws on the
5.
wall.
Mark the lower holes.
6.
Remove the extractor hood from the wall.
7.
Drill the lower holes.
8.
Hang the extractor hood on the upper screws on the
9.
wall.
Tighten the upper and lower screws by hand.
10.