Electrolux EIFLW55HMB - 27" Front-Load Washer Technisch gegevensblad - Pagina 2

Blader online of download pdf Technisch gegevensblad voor {categorie_naam} Electrolux EIFLW55HMB - 27" Front-Load Washer. Electrolux EIFLW55HMB - 27" Front-Load Washer 16 pagina's. Iq-touch front-load washer
Ook voor Electrolux EIFLW55HMB - 27" Front-Load Washer: Specificaties (2 pagina's), Gebruiks- en onderhoudshandleiding (32 pagina's), Specificatie (2 pagina's), (Spaanse) Gebruiks- en Onderhoudshandleiding (36 pagina's), (Frans) Gebruiks- en onderhoudshandleiding (36 pagina's)

Pagina afdrukken

2. Turn the program knob (1) click clockwise from the start position. The hot water solenoid will activate and hot water should

enter through the detergent compartment.

3. Turn the program knob (2) clicks from the start position. The bleach water solenoid will activate and cold water should enter

through the bleach compartment.

4. Turn the program knob (3) clicks from the start position. The bleach and the wash water solenoids will activate and cold

water should enter through the softener compartment.

5. Turn the program knob (4) clicks from the start position. The prewash solenoid will activate and cold water should enter

through the prewash compartment.

6. Turn the program knob (5) clicks from the start position. The door lock solenoid will deactivate and the loading door can be

opened. When the door is opened, the drum light should turn on.

7. Turn the program knob (6) clicks from the start position. The door lock will activate and the washer will fill then tumble.

Once tumbling has started, the Boost Heater will turn on.

8. Turn the program knob (7) clicks from the start position. The drain pump will activate draining out any water in the tub and

the washer will operate in high spin.

9. Turn the program knob (8) clicks from the start position. This is a free position.

10. Turn the program knob (9) clicks from the start position. The control will signal the last 5 error codes with E00 being no

error.

11. Turn the program knob (10) clicks from the start position. Latest software version will be shown.

12. If applicable, turn the program knob (11) clicks from the start position. This is a free position.

Exiting Diagnostic Mode

To return the washer to normal operation:

a) Unplug the power cord, wait 5-8 seconds, then reconnect the power cord OR

b) Turn the program knob clockwise back to the Start Position. Press the "Cancel" and far left button under the

display until the LEDs stop flashing.

FACTORY RESET

1. 1¼"x2" display models, wake machine, push the spin speed and soil selection keys simultaneously and hold until you hear

a beep. This is no more than 10 seconds.

2. 1¼"x4¾" display models, scroll through the option key until you get to the preference selection (PREF). Once there, push

the select key then scroll through this menu until you get to the reset selection and push the select key. From here, you

have the selection of the type of reset you wish to perform. Make your selection and push the select key. The machine will

turn off and when woken up, the part(s) of the program you wanted reset are now set back to factory settings.

INSTALLATION CYCLE

Before entering the Installation Cycle (Install Cycle) make sure that all articles are out of the drum (the drum is empty).

1¼"x2" Display Models

1. Wake the washer up by pressing any button (except the cancel button).

2. Rotate the cycle knob to the "Hand Wash" cycle.

3. Press the "Start/Pause" button, then the "Cancel" button.

4. Wake the unit up again, immediately and simultaneously press and hold the "My Favorite" and "ECO Friendly" buttons

for 5 seconds. The display will show "INSTAL CYCLE" with the estimated time of cycle completion.

5. Press the "Start/Pause" button to begin the cycle. Installation cycle will test for electronic issues, wiring issues & water

flow issues. At cycle completion, the display will show "INSTAL PASS!" or prompt an action during the cycle such as "CALL

SERVICE", "NO WATER" or "CHECK HOSES". Correct the action and repeat the cycle for proper installation. Washer will

exit the Install Cycle and return to normal operation the next time the knob is turned.

1¼"x4¾" Display Models

1. The machine will first wake up on setting up the unit to display language selection. Press NEXT to display the Install cycle.

You can run it now if you choose. If you don't want to run it immediately, you can access the Install cycle through the PREF

menu in the option window. Press the select key once you scroll to the PREF selection. Then scroll through this menu until

you get to the Install cycle. Press the select key then follow the instructions (remove all articles from the washer drum).

You can also get to this cycle by performing a full reset of factory settings.