Formica Intentek Technische handleiding Gebruik en verzorging, garantie en installatiehandleiding - Pagina 3
Blader online of download pdf Technische handleiding Gebruik en verzorging, garantie en installatiehandleiding voor {categorie_naam} Formica Intentek. Formica Intentek 17 pagina's. Wireless charging surface
Pagina afdrukkenINTENTEK
WIRELESS CHARGING SURFACE
™
TECHINCAL GUIDE USE & CARE, WARRANTY, AND INSTALLATON GUIDE
WPC, QI AND QI CERTIFICATION
Qi (pronounced "chee") is the predominant standard for wireless
charging. The standard is governed by the Wireless Power
Consortium (WPC) which has more than 575 member companies. To
date, more than 500 million Qi enabled receivers have been shipped.
Qi Certified products have passed rigorous, independent laboratory
tests for safety, interoperability, energy efficiency and quality. To be
certified, they must work with all Qi wireless products regardless
of brand or manufacturer. Qi certification ensures that devices (the
power receivers) and chargers (the power transmitters) always
worktogether for simple and easy charging.
INCORPORATION OF INTENTEK
CHARGING SURFACES INTO FURNITURE DESIGN:
TIPS & BEST PRACTICES
Location of the charging zones will vary from project to project.
The following points represent tips and best practices that should
be considered for placement of the charging zones only. Formica
Group is not responsible and assumes no liability for the design,
engineering, installation, assembly or structural integrity of the
fabricated piece.
•
Cavity for electronics module must be at least 1" from all
edges of table/top.
•
Blower direction can point up, down, left, or right
(at 90°, 180°, 270°, or 360°).
•
Blower inlet and outlet cannot be covered by pedestal, leg, or
other obstruction.
OUTLET
INLET
FTB-0918 | Rev 2 | 6/20
WIRELESS
™
•
When placing charging zones near each other, we recommend ..
at least 11" is left between center points of the charging icons.
The electronic module casing must be at least 1" apart.
•
When placing two electronics modules near each other, a
blower inlet must be at least 8" from another blower's outlet.
This rule is to be followed only if blower inlet and outlet are
designed to be near each other.
•
If Intentek
System is going to be used in an enclosed counter
™
(i.e. on top of a cabinet or drawer), the enclosed space must
be properly vented. Vent determination is the responsibility
of the furniture designer. Venting must be sufficient to support
the blower at 2CFM.
•
Electronics module cannot be in direct contact with
obstructions: edges, screws, pedestals/legs.
TO ORDER
Call 1-800-FORMICA
or visit here:
™
us/campaigns/intentek/intentek-inquiry-form
GENERAL SAFETY
Please read this Technical Guide, Use & Care, Warranty, and
Installation Guide and all warnings contained herein prior to handling
the Intentek
System.
™
CUSTOMER SAFETY
1. For indoor use only.
2. Do not overload electrical outlets.
3. AC Adapter must be plugged into a compatible mains supply to
operate.
4. Intentek
Electronics AC Adapter or equivalent must be used.
™
5. Never use the AC Adapter if damaged in any way.
6. When using the AC Adapter or extension cord, confirm safety
precautions have been made so there are no tripping hazards.
7. Keep any wiring used to connect Electronics Modules covered.
CUSTOMER USE & CARE AFTER INSTALLATION
1. Do not unscrew the electronics module housing without
professional support. If internal parts are ever exposed, avoid
contact with sharp objects and moisture.
2. May not be housed outside of recommended temperature range.
3. May not be stored outdoors.
4. At all times, keep electronics module and AC adapter away from
liquids.
5. Do not place foreign or sharp objects in the electronics module
or or blower inlet/outlet.
6. Follow all cleaning instructions for decorative surface. Do not
attempt to clean inside of electronics module.
Formica Group Technical Guide
| 3
https://www.formica.com/en-