Bosch 300 Series Gebruiks- en onderhoudshandleiding / Installatie-instructies - Pagina 34

Blader online of download pdf Gebruiks- en onderhoudshandleiding / Installatie-instructies voor {categorie_naam} Bosch 300 Series. Bosch 300 Series 40 pagina's. Built-in wall ovens
Ook voor Bosch 300 Series: Gebruiksaanwijzing (40 pagina's), Gebruikershandleiding (21 pagina's), Installatiehandleiding (6 pagina's), Installatiehandleiding (36 pagina's), Installatiehandleiding (32 pagina's), Gebruiksaanwijzing (50 pagina's), Snelstart- en veiligheidshandleiding (7 pagina's), Installatiehandleiding (28 pagina's), Snelstarthandleiding (7 pagina's), Gebruiks- en onderhoudshandleiding (32 pagina's), Snelstart- en veiligheidshandleiding (7 pagina's), Servicehandleiding (36 pagina's), Snelstart- en veiligheidshandleiding (13 pagina's)

Bosch 300 Series Gebruiks- en onderhoudshandleiding / Installatie-instructies
Problem
Creasing.
Drying result is not sat-
isfactory (laundry feels
too damp).
Drying time too long.
Program does not start
Finish in (remaining)
time is displayed.
Program does not start
-
symbol lit up.
D
One or more indicator
lights are flashing.
Power failure.
34
Possible cause(s)
Laundry load exceeded.
Unsuitable program selected.
Warm laundry may feel more damp
than it really is.
The selected program does not suit
the load.
Dryness level is not adjusted.
Fine layer of limescale or detergent
and textile care products residues
on the moisture sensors.
Program termination e.g. main
power supply failure, door open or
maximum drying time reached.
Initial load is too wet.
Lint filter and/or Heat Exchanger is
dirty.
Insufficient supply of air.
Air inlet possibly blocked.
Ambient temperature higher than
°
°
95
F/35
C.
A delayed starting time has been
selected and activated.
Childproof look is activated.
Lint filter or/and heat exchanger is
dirty.
Installation conditions are not ade-
quate.
Fault in program sequence or mal-
function.
Solution(s)
Do not exceed the maximum load for selected pro-
gram. Remove items of laundry immediately after the
end of the program, hang them up and pull into shape.
Turn program selector to Off.
~ Program selection table; Page 26
Select Wrinkle Block button to prevent the laundry
from creasing or wrinkling.
~ Wrinkle Block; Page 27
Remove items of laundry immediately after the end of
the program and turn the program selector to Off.
Use another drying program or, in addition, select the
time program.
~ Program selection table; Page 26
Use Dry Level to adjust the dryness level.
~ Dry Level; Page 27
Clean the moisture sensors.
~ Cleaning the moisture sensors; Page 31
See the problem(s) mentioned in this table.
Spin laundry at higher speed in the washing machine,
before drying.
Switch off the dryer, and than turn it on again.
Clean lint filter
~ Cleaning the lint filter; Page 29
and/or Heat Exchanger.
~ Cleaning the heat exchanger; Page 30
Ensure that air can circulate.
Do not obstruct the air inlet on the front of the dryer.
Ventilate the room.
Drying cycle will begin at proper time to complete at
the selected Finish in time.
Deactivate Childproof look.
~ Childproof lock; Page 23
Clean lint filter or/and heat exchanger (see solution of
the problem(s) in this table above).
Check the installation conditions.
~ Electrical Connections; Page 14
Switch off the dryer, allow it to cool down, switch back
on and restart the program.
Remove laundry from the dryer immediately and
spread out. This allows the heat to dissipate. Be care-
ful as the door, the drum and the laundry may be hot.