Advanced Measurement Technology ORTEC A-576 A-PAD Bedienings- en onderhoudshandleiding - Pagina 6
Blader online of download pdf Bedienings- en onderhoudshandleiding voor {categorie_naam} Advanced Measurement Technology ORTEC A-576 A-PAD. Advanced Measurement Technology ORTEC A-576 A-PAD 11 pagina's. Preamplifier, amplifier, discriminator with bias supply
Pagina afdrukken
2.1. PERFORMANCE
DETECTOR AND ELECTRONIC NOISE <25 keV
FWHM when used with ORTEC R Series, 300 mm
2
and 450 mm charged-particle detectors, and <35 keV
2
for 600 mm and 900 mm R Series charged-particle
detectors when connection of the Model A-576 to the
detector is made with <2 ft of RG-62A/U cable.
System noise is dependent on detector capacitance
plus cable capacitance and leakage current. Electronic
noise is typically 5 keV with a slope of 25 eV/pF silicon
equivalent (based on
(internal amplifier).
PULSE SHAPING Internal 0.5-µs active filter semi-
Gaussian pulse shaping amplifier provides a pulse that
is stretched prior to being output through the Bias
Amplifier to give a 4-µs-wide positive output pulse.
ENERGY RANGES 3 TO 8 MeV, 4 to 7 MeV, 3 to 5
MeV, 4 to 6 MeV, 5 to 7 MeV, 6 to 8 MeV.
CALIBRATED TEST PULSER
5 MeV, 6 MeV, or 7 MeV. (Shipped at 5 MeV). Rate is
100 Hz.
DETECTOR BIAS VOLTAGE Continuously variable
over range of 0 to 100 V. Polarity selectable with
printed wiring board (PWB) jumper shipped in negative
position (appropriate for ORTEC R Series detectors).
Shipped set to 100 V.
2.2. CONTROLS
TEST/BIAS/OFF Front-panel, three-position toggle
switch controls both the detector bias voltage and the
test pulser. Front-panel LED is illuminated when the
bias voltage is on.
DET BIAS ADJ Front-panel potentiometer for
controlling the bias voltage applied to the detector.
Continuously variable from 0 to ±100 V.
2. SPECIFICATIONS
2
= 3.6 eV and t = 0.5 µs
Equivalent Energy
2
ENERGY RANGE Six positions on the front-panel
switch for selecting the desired energy range (see
PERFORMANCE).
2
E BIAS 15-turn potentiometer on the front panel
permits screwdriver adjustment of the energy output
bias point to be varied by ±10% for ease of setup with
the data acquisition system.
E 15-turn potentiometer on the front panel permits
screwdriver adjustment of the maximum energy output
range to be varied from 7.75 to 10.25 V for ease of
setup with the data acquisition system.
TEST PULSER PWB jumper (J2) allows selection of
internal pulser energies of 5 MeV, 6 MeV, or 7 MeV.
INPUT/BIAS POLARITY PWB jumpers allow
selection of either positive or negative detector voltage
polarity. Negative for ORTEC Surface Barrier or Ion-
Implanted Ruggedized detectors, or positive for
conventional detectors. (Shipped in Negative position.)
PREAMP IN Front- and rear-panel BNCs accept an
input signal from semiconductor charged-particle
detectors. Either RG-62A/U or RG-71A/U cable is
recommended to minimize excess capacitance and
hence noise.
ENERGY Front- and rear-panel BNC connectors
provides a positive stretched pulse from 7.75 to
10.25 V maximum, depending on the setting of the
gain control corresponding to an energy range
selected on the front-panel switch. Pulse width =
4 µs; Z = 100
0
2.3. INPUT
2.4. OUTPUTS
6
; dc-coupled.
E