Andis BDC Gebruiks- en onderhoudsinstructies Handleiding - Pagina 2

Blader online of download pdf Gebruiks- en onderhoudsinstructies Handleiding voor {categorie_naam} Andis BDC. Andis BDC 12 pagina's.

E N G L I S H
Please read the following instructions before using your new Andis
clipper. Give it the care that a fine, precision built instrument
deserves and it will give you years of service.

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic precautions should
always be followed, including the following: Read all
instructions before using the Andis clipper.
DANGER:
To reduce the risk of electric shock:
1. Do not reach for an appliance that has fallen into water.
Unplug immediately.
2. Do not use while bathing or in a shower.
3. Do not place or store appliance where it can fall or be pulled
into a tub or sink. Do not place in or drop into water or other
liquid.
4. Always unplug this appliance after use.
5. Unplug this appliance before cleaning, removing or
assembling parts.
WARNING:
To reduce the risk of burns, fire, electric
shock, or injury to persons:
1. An appliance should never be left unattended when plugged in.
2. This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
3. Children should be supervised to ensure that they do not play
with the appliance.
4. Use this appliance only for its intended use as described in this
manual. Do not use attachments not recommended by Andis.
5. Never operate this appliance if it has a damaged cord or
plug, if it is not working properly, if it has been dropped or
damaged, or dropped into water. Return the appliance to an
Andis authorized service station for examination and repair.
2
6. Keep the cord away from heated surfaces.
7. Never drop or insert any object into any opening.
8. Do not use outdoors or operate where aerosol (spray) products
are being used or where oxygen is being administered.
9. Do not use this appliance with a damaged or broken blade or
comb, as injury to the skin may occur.
10. To disconnect turn control to OFF then remove plug from outlet.
11. WARNING: During use, do not place or leave appliance
where it may be (1) damaged by an animal or (2) exposed
to the weather.
12. This appliance is intended for trimming purposes only.
SAVE THESE INSTRUCTIONS
THIS PRODUCT INTENDED FOR HOUSEHOLD USE
OPERATING INSTRUCTIONS
To reduce the risk of electric shock, this appliance has a polarized plug (one
blade is wider than the other). This plug will fit in a polarized outlet only one
way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not
fit, contact a qualified electrician to install the proper outlet. Do not change the
plug in any way.
Plug cord into electrical outlet, operate at 120 volt, 60 cycle AC electrical current
or as noted on the unit.
2-SPEED OPERATION
Your Andis clipper is equipped with two cutting speeds. The speeds are adjusted
using the slide switch actuator on the top of the unit (Figure A). Setting "O"
indicates the off position, Setting "1" is low speed and Setting "2" is high
speed. After using your Andis clipper, rewrap cord and store in a safe place.
REMOVING BLADE SET
To remove blade set, first make sure your clipper motor is switched OFF. Push
blade release mechanism under blade hinge (Figure B). While holding down the
blade release mechanism, push down on blade, then gently pull the blade
forward (Figure C), and slide it off the blade hinge. If your blade hinge should
snap closed and is flush with the clipper, use a small standard screwdriver to pry
the tongue of the hinge out (Figure D). NOTE: Hair may accumulate in the front
cavity of the housing under the blade. If this happens, you can clean out the hair
by brushing out the cavity with a small brush or an old toothbrush while the
blade is off the clipper.
3