Andis BGC Gebruikershandleiding - Pagina 2

Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Andis BGC. Andis BGC 2 pagina's. Andis model bgc clippers
Ook voor Andis BGC: Gebruik en verzorging (2 pagina's)

Pagina afdrukken

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic precautions

should always be followed, including the following:

Read all instructions before using the Andis Clipper.

DANGER:

To reduce the risk of electric shock:

1. Do not reach for an appliance that has fallen

into water. Unplug immediately.

2. Do not use while bathing or in a shower.

3. Do not place or store appliance where it can

fall or be pulled into a tub or sink. Do not place

in or drop into water or other liquid.

4. Always unplug this appliance from the electrical

outlet immediately after using.

5. Unplug this appliance before cleaning, remov-

ing, or assembling parts.

WARNING:

To reduce the risk of burns,

fire, electric shock, or injury to persons:

1. An appliance should never be left unattended

when plugged in.

2. Close supervision is necessary when this appli-

ance is used by, on, or near children or invalids.

3. Use this appliance only for its intended use as

described in this manual. Do not use attach-

ments not recommended by Andis.

4. Never operate this appliance if it has a dam-

aged cord or plug, if it is not working properly, if

it has been dropped or damaged, or dropped

into water. Return the appliance to an Andis

Service Center for examination and repair.

5. Keep the cord away from heated surfaces.

6. Never drop or insert any object into any opening.

7. Do not use outdoors or operate where aerosol

(spray) products are being used or where oxy-

gen is being administered.

8. Do not use this appliance with a damaged

comb or broken blade, as injury to the skin may

occur.

9. To disconnect turn control to "off" then remove

plug from outlet.

SAVE THESE INSTRUCTIONS

SERVICING OF A DOUBLE-INSULATED CLIPPER

In a double-insulated clipper, two systems of insulation

are provided instead of grounding. No grounding means

is provided on a double-insulated clipper, nor should a

means for grounding be added. Servicing a double-insu-

lated clipper requires extreme care and knowledge of the

system, and should be done only by an Andis Authorized

Service Station. Replacement parts must be identical to

those parts being replaced. A double-insulated clipper is

marked by the words "DOUBLE INSULATION" or "DOU-

BLE INSULATED". The symbol

may also be

marked on the appliance.

OPERATING INSTRUCTIONS

Please read the following instructions

before using your new Andis Clipper.

Give it the care that a fine precision built

instrument deserves and it will give you

years of service. Plug cord into electrical outlet, operate

120 volt, 60 cycle AC electrical current or as noted on

unit. To start clipper move switch button to the # 1

position. To stop, move switch button back to original

position.

REMOVING BLADE SET

To remove blade set, first make sure your clipper

motor is switched "OFF", then push down on blade

with one or both thumbs (Diagram A) and slide

blade off blade hinge. If your blade hinge should

snap closed and is flush with the clipper, use a

small standard screwdriver to pry the tongue of the

hinge out (Diagram B).

NOTE: Hair may accumulate in the front cavity of

the housing under the blade. If this happens, you

can clean out the hair by brushing out the cavity

with a small brush or an old toothbrush while the

blade is off the clipper (See Diagram C for location

of cavity being referenced).

DIAGRAM A

DIAGRAM B

DIAGRAM A

DIAGRAM C

DIAGRAM D

REPLACING OR CHANGING BLADE SET

To replace or change your blade set, slide the blade

bracket onto the hinge of the clipper (Diagram D)

and with the clipper turned "ON", push the blade

towards the clipper to lock into position.

USER MAINTENANCE

The internal mechanism of your motor clipper has

been permanently lubricated by the factory. Other

than the recommended maintenance described in

this manual, no other maintenance should be per-

formed, except by Andis Company, or an Andis

Authorized Repair Service Station.

This Product intended for Professional Use

CARE AND SERVICING OF YOUR ANDIS

CLIPPER BLADES

Blades should be oiled before, during, and after

each use. If your clipper blades leave streaks or

slow down, it's a sure sign blades need oil. Place a

few drops of oil on the front and side of the cutter

blades (Diagram E). Wipe excess oil off blades with

a soft, dry cloth. Spray lubricants contain insufficient

oil for good lubrication, but are an excellent clipper

blade coolant. Always replace broken or nicked

blades to prevent injury. You can clean the excess

hair from your blades by using a small brush or

worn out toothbrush. To clean the blades, we sug-

gest to immerse the blades only into a shallow pan

of Andis Clipper Oil, while the clipper is running. Any

excess hair and dirt that has accumulated between

the blades should come out. After cleaning, turn

your clipper off and dry blades with a clean dry cloth

and start clipping again. If upon cleaning your

blades you find that the blades will still not cut, there

may be a few fine pieces of hair trapped between

the upper and lower blade. If this happens, you will

need to snap the blade off the clipper. Proceed to

slide the upper blade to one side, without loosening

the tension spring or moving the upper blade com-

pletely out from under the tension spring (See

Diagram F for position of blade). Wipe the surface

between the blades clean with a dry cloth, then

place a drop of clipper oil

OIL

where the upper and lower

blades meet and also in the

guide slot of the tension spring

OIL

(Diagram F). Now slide the

upper blade to the opposite

side of the lower blade and

DIAGRAM E

repeat this process. After com-

pleting this procedure, slide the

upper blade, centering it over

the lower blade. Handle or

store your Andis Clipper with

the blades down so excess oil

will not run into the clipper

case.

DIAGRAM F

CAUTION: Never handle your Andis Clipper while you

are operating a water faucet and never hold your clip-

per under a water faucet or in water. There is danger

of electrical shock and damage to your clipper.

ANDIS COMPANY will not be responsible in case

of injury due to this carelessness.

HINGE KITS

Hinge packed with clipper for

Hinge assembled on clipper for

use with Andis Model BG

Blades and Oster Models 10,

Blades and Oster Model 76

22, & 111 Blades

Blades

OIL