(7)
On/off switch
(8)
Speed preselection thumbwheel (GSB 16 RE)
(9)
Auxiliary handle (insulated gripping surface)
A)
(10) Depth stop
(11) Handle (insulated gripping surface)
A)
(12) Chuck key
A)
(13) Keyed chuck
Technical Data
Impact drill
Article number
Rated power input
Power output
No-load speed
Impact rate
Rated torque
Speed preselection
Right/left rotation
Spindle collar diameter
Max. drilling diameter
– Concrete
– Steel
– Wood
Chuck capacity
Weight according to EPTA-
Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.
Assembly
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Auxiliary Handle (see figure A)
Do not operate your power tool without the auxiliary
u
handle (9).
You can swivel the auxiliary handle (9) to any angle for a safe
work posture that minimises fatigue.
Turn the lower gripping end of the auxiliary handle (9) anti-
clockwise and set the depth stop (10).
Pull the depth stop far enough out that the distance between
the drill bit tip and the edge of the depth stop corresponds
to the required drilling depth X.
Then, turn the lower gripping end of the auxiliary handle (9)
clockwise to retighten it.
The fluting on the depth stop (10) must face upwards.
Bosch Power Tools
A)
GSB ...
13
3 601 ...
B27 0..
W
650
W
353
rpm
3 150
rpm
47 000
Nm
1.8
–
–
mm
43
mm
13
mm
10
mm
20
mm
1.5–13
kg
1.6
/ II
(14) Universal bit holder
A)B)
(15) Screwdriver bit
A)B)
(16) Hex key
(17) Open-ended spanner
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
B) Commercially available (not included in the scope of deliv-
ery)
13 RE
16
B27 1..
B28 0..
650
750
353
456
3 150
3 250
47 000
48 500
1.8
2.1
–
●
43
43
13
16
10
12
20
25
1.5–13
1.5–13
1.6
1.8
/ II
/ II
Changing the Tool
Keyless Chuck (see figure B)
Hold the rear sleeve (3) of the keyless chuck (1) firmly and
turn the front sleeve (2) in the rotational direction ➊ until
the tool can be inserted. Insert the tool.
Hold the rear sleeve (3) of the keyless chuck (1) and firmly
tighten the front sleeve (2) by hand in the rotational direc-
tion ➋ until it stops clicking. This will automatically lock the
drill chuck.
The lock will disengage again if you turn the front sleeve (2)
in the opposite direction to remove the tool.
Keyed chuck (see figure C)
Wear protective gloves when changing tools. The drill
u
chuck may heat up significantly when it is used for long
periods.
Open the keyed chuck (13) by turning it until the tool can be
inserted. Insert the tool.
Insert the drill chuck key (12) into the corresponding holes
of the keyed chuck (13) and clamp the tool evenly.
English | 11
A)
A)B)
16 RE
600 RE
B28 1..
B27 1..
750
456
3 250
48 500
47 000
2.1
–
●
–
●
43
16
12
25
1.5–13
1.5–13
1.8
/ II
1 609 92A 4H1 | (10.10.2018)
650
353
3 150
1.8
–
●
43
13
10
20
1.6
/ II
Pagina afdrukken