Andres Industries Car Cradle Gebruiksaanwijzing - Pagina 2
Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Andres Industries Car Cradle. Andres Industries Car Cradle 2 pagina's. For aishell mini / mini+ / air / 10 / pro 12.9
Instruction manual Car Cradle
for aiShell™ mini / mini+ / Air / 10
Content:
1×
Car Cradle Top
1|
1×
Car Cradle Base
2|
4×
Screws
3|
ISO 4762 - M4×18
1×
Allen key SW3
4×
Locknuts
4|
DIN 985 - M4
4×
Washers
4|
DIN 125 - 4.3 (M4)
Optionally in the scope of delivery:
1×
Car Cradle Connector
2×
Screws (preassembled)
DIN 912 - M3×6
1×
O-Ring (already installed)
6×1.2 mm
1×
Allen key SW2.5
Car Cradle Pro for aiShell™Pro 12.9
Inhalt:
1×
Car Cradle Top
6|
1×
Car Cradle Mid
7|
1×
Car Cradle Base
8|
4×
Screws
9|
ISO 7380 - M4×8
4×
Screws
10|
ISO 7380 - M4×20
1×
Allen key SW 3
4×
Locknuts
11|
DIN 985 - M4
Optionally in the scope of delivery:
1×
Car Cradle Connector
2×
Screws (preassembled)
DIN 912 - M3×6
1×
O-Ring (already installed)
6×1.2 mm
1×
Allen key SW2.5
Feedthrough for Car Cradle and Car Cradle Pro:
1.
Put the iPad into the proper aiShell™ according to the manual
provided with the case.
2.
Open the lower rubber plug to get access to the loading part.
3.
Attach the Connector of the Car Cradle and slightly tighten the M3
screws with a hexagon socket screwdriver until it is firmly seated.
4.
Connect the Car Cradle to a battery charger (5,0–5,2V / 2,0 – 2,5A)
that is certified for the Apple iPad (MFI) you are using. Therefor use
the USB plug.
5.
Place the aiShell™ in the Car Cradle with the Connector going in first
until the aiShell snaps into the Car Cradle.
6.
To remeove the aiShell™ push the upper snap-fit upwards with your
thumb and pull out the aiShell™ with an upward movement.
Andres Industries AG
CEO: Dr. Björn Andres
1|
3|
2|
6|
7|
9|
10|
9|
8|
Weißenseer Weg 37
Tel.: +49 (0) 30 45 80 39 00
13055 Berlin
Fax: +49 (0) 30 45 80 39 03
Preparation:
The two parts of the Car Cradle have to be attached to
each other or additionally to a RAM-Mount
5|
5|not provided)
4|
locknuts. For the use with an aiShell™ mini or mini+ use
the four upper bores of the Car Cadle top and for the use
with an aiShell™ Air or Pro 10.5 use the lower bores.
Preparation:
The three parts of the Car Cradle have to be attached to
each other or additionally to a RAM-Mount
5|not provided)
locknuts.
The Car Cradle top and the Car Cradle base are placed
against each other on top of the Car Cradle mid that
5|
the outer contours and screw holes coincide. The M4×8
screws are used for the two upper holes (on Car Cradle
11|
top) and the two lower holes (on Car Cradle base). For the
four remaining middle holes of the Car Cradle correspon-
ding the M4×20 screws to fix the RAM-Mount
in the scope of
ATTENTION!
Before the iPad can be removed from the aiShell™ the Connector
HAS TO BE removed. Afterwards for the removal of the iPad
follow the steps described in the aiShell manual vice versa. If
you try to remove the iPad with the Connector attached to the
aiShell™ the Connector and iPad will be damaged!
(RAM-202U,
with the provided screws, washers and
(RAM-202U,
with the provided screws, washers and
(Optionally
delivery).
Mail: [email protected]
www.andres-industries.de