Atlantic Technology 8200 System Gebruiksaanwijzing - Pagina 17

Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Atlantic Technology 8200 System. Atlantic Technology 8200 System 20 pagina's. Pedestal subwoofer systems
Ook voor Atlantic Technology 8200 System: Beoordelingshandleiding (3 pagina's), Gebruiksaanwijzing (12 pagina's)

Atlantic Technology 8200 System Gebruiksaanwijzing
Instruction Manual
EQ4
EQ4 - We call EQ4
EQ4 - We call EQ4
After Dark. At lower volume levels human hear-
ing is less sensitive at the frequency extremes (deep bass and very high
sounds).In order to compensate when you must play the system at lower
volume levels,EQ4 has been designed to raise the overall bass output of
the sub slightly.The result will be a fuller and richer sounding bass at low
volumes.EQ4 is designed for both music and movies.It can also be used
to help compensate for lack of bass at the listening position.
REF - This resets the EQ to flat response and the also resets the volume
trim to 0dB.
LEVEL TRIM and MUTE - The  and
���
���
���
the total output level of your subwoofer to compensate for soundtrack
variations and your personal preferences.Each push of the button results
���
���
����
����
the volume of the PedWoofers. Pressing it again returns the volume to
its previous setting.

Direct Access Connector

Located on the rear panel, this port and the corresponding male plug
(shipped installed in the port) is for use with a hard wired remote control
system using electronic or mechanical switching.Each contact function
is labeled.To access the control functions use a normally open connec-
tion.Momentary closure will activate each function.The LEVEL TRIM
Problem
No bass output
Audible buzz or hum
Weak bass: vague stereo image
 and
 buttons let you change
 buttons let you change
in a 1dB change above or below the
preset reference set with the BASS
LEVEL control. The LEVEL TRIM
readout on the amplifier indicates
the level of adjustment in dB.
Pressing the MUTE button turns off
Possible Cause
AC power cord unplugged or
plugged into a non-working outlet.
Input cables not securely
connected or defective.
Input cable not securely connected
or defective.
Ground loop through antenna or
cable TV system input.
Input source connected to HI LEVEL
inputs is wired out of phase.

PedWoofer Troubleshooting Guide

function will respond in 1dB steps to a single contact closure while con-
stant closure will result in continuous steps to the maximum of ± 10dB.
The REF EQ and REF volume reset functions each have their own set
of contacts.
Care and Feeding of Your
PedWoofer System
The duraBlac enclosure finish can be cleaned with a water dampened
cloth and dried with a soft cotton towel. Their duraBlacTM finish is a
matte lacquer paint that should be treated like any fine painted surface.
The amplifier can be wiped with a clean,dry cloth.If necessary,you can
clean the front panel with a soft cloth moistened with mild window
cleaner or dampened slightly with water.
slightly with water.
slightly
IMPORTANT: SAVE YOUR BOXES! If you can do so, save the
carton, packing pieces and plastic bags that came with your sub-
woofer. They will be useful in case you move or have to ship your
subwoofer for any reason. In any case, save all packing materials
until you are certain that the system has suffered no damage in
shipment. If you find such damage, either visible or internal, con-
tact your dealer immediately for the proper return procedure.
PedWoofer Troubleshooting Guide
Once your PedWoofers are set up,you should have many years of mainte-
nance free enjoyment from your system.However,if you should encoun-
ter a problem,refer to the following guide to help find the solution.If the
problem persists, please contact your local authorized Atlantic Technol-
ogy dealer.
Possible Solution
Plug into a working outlet.
Check all connections, then try another
input cable.
Check all connections, then try another
input cable.
Test by disconnecting antenna and/or cable
system input leads. If hum goes away, install
isolation balun(s) at that point.
Check speaker wire connections and
reconnect in proper phase.
17