Atlas Copco G2417 S250 Product Instructies - Pagina 5

Blader online of download pdf Product Instructies voor {categorie_naam} Atlas Copco G2417 S250. Atlas Copco G2417 S250 12 pagina's.

Pagina afdrukken

G2417 S250

Maintain a balanced body position and firm foot-

►

ing

React quickly to excessive vibration due to dam-

►

aged, or improperly mounted insert tool

Keep away from rotating drive spindle and abras-

►

ives. Rotation may continue for several seconds

after the throttle has been released. Do not lay the

tool down until rotation has stopped

Observe that stored compressed air in the hose

►

may cause an accidental start

Release control device if the energy supply should

►

fail

Maintenance

Rust protection and internal cleaning

Water in the compressed air, dust and wear particles

cause rust and sticking of vanes, valves etc.

This can be solved by lubricating with oil (a few

drops), running the machine for 5-10 seconds and

wiping off excess oil with a cloth. Do this before

longer standstills.

Lubrication

The front motor ball bearing should be lubricated

with grease in conjuction with the regular overhaul

of the machine.

For flexible spindle extension – When fitting the

extended spindle – apply 0.5 cm

"Lubricating Engineers LE3752" (or EP grease) at

the bottom of the hole in the collet holder.

Lubricating guide

Use lubricants of good quality. The oils and greases

listed in the lubrication table are examples of lubric-

ants that can be recommended.

Brand

General purpose

Bearings

Energrease LS-EP2

Castrol

Spheerol EP L2

Esso

Beacon EP2

Rembrandt EP2

Mobil

Mobilegrease XHP 222

Shell

Alvania EP2

Texaco

Multifak EP2

Molycote

BR2 Plus

of grease type

Air lubrication

Energol E46

Arox EP46

Chopin 46

Almo oil 525

Tonna R32

Aries 32

Safety and operating instructions

Overhaul

WARNING Overspeed could result in serious

injury or death

If governor is used, check that correct governor

►

is assembled. Careless handling may put it out of

order

Do not disassemble security parts, e.g. speed

►

governor or overspeed shut-off. These parts must

be completely replaced when damaged

Always check the free speed of the machine after

►

service. See Section Preparation before using the

die grinder

The entire machine should be checked regularly at

six-month intervals. If it is in heavy duty service or

not running properly it should be taken out of service

more often for inspection.

The strainer at the air inlet should be cleaned fre-

quently to prevent clogging and decreased capacity.

Useful information

C Log in to Atlas Copco www.atlascopco.com

You can find information concerning our products,

accessories, spare parts and published matters on our

website.

Ergonomic guidelines

Consider your workstation as you read through this

list of general ergonomic guidelines and see if you

can identify areas for improvement in posture, com-

ponent placement, or work environment.

• Take frequent breaks and change work positions

frequently.

• Adapt the workstation area to your needs and the

work task.

• Adjust for convenient reach range by determin-

ing where parts or tools should be located to

avoid static load.

• Use workstation equipment such as tables and

chairs appropriate for the work task.

• Avoid work positions above shoulder level or with

static holding during assembly operations.

• When working above shoulder level, reduce

the load on the static muscles by reducing the

weight of the tool, using for example torque

arms, hose reels or weight balancers. You can

also reduce the load on the static muscles by

holding the tool close to the body.

• Make sure to take frequent breaks.

• Avoid extreme arm or wrist postures, particu-

larly for operations requiring a degree of force.