FoxESS LV54 Snelle installatiehandleiding

Blader online of download pdf Snelle installatiehandleiding voor {categorie_naam} FoxESS LV54. FoxESS LV54 3 pagina's.

Pagina afdrukken
LV54 quick Installation guide
1. Tools Required
The following tools will be required to install the battery.
Screw driver
Crimping modular
Safety shoes
Safety gloves
Safety goggles
Plier
Spanner
Ribbon
Electric Drill
Track Level Bar
2. Packing List
Please check if following items are including with the package:
A
B
C
D
E
G
H
Quick
Installation
Guide
K
I
J
Description
Object Quantity
A
1
Battery
B
1
Bracket
Expansion Tubes&
C
5+5
Expansion Screws
D
4
Set screw
E
2
Earth Terminal
F
2
Plug（to short pin1 and pin6）
G
1
Communication Network Cable(3m)
H
1
Ground Wire(3m)
I
1
Quick Installation Guide
J
1
Power Line（3m）
Communication Network Cable (3m)
K
1+1
(Inverter to Battery)（RS485&CAN)
K: In order to match different inverters, two kinds of communication cables
(RS485 & CAN) are provided with the package.The battery side plug is
already crimped, the inverter side please refer to inverter's manual for
the pin definition.
K-1
RS485 (Battery side)
Please plug into the PCS
port of the ba�ery.
RS485 (Battery side) Pin definition:
Pin
1
2
3
4
Definition
NC
NC
RS485-B
NC
Multimeter
K-2
CAN(Battery side)
Please plug into the PCS
port of the ba�ery.
CAN (Battery side) Pin definition:
Pin
1
2
3
4
Definition
NC
NC
NC
CANL
Note: The definition of the inverter side end plug needs to be crimped in
accordance with the inverter's manual.
Note:
1. Use only the parts included with the battery pack to ensure proper
installation. If anything is damaged or missing, contact manufacturer
or your distributor.
2. Select a communication cable (CAN/RS485) based on the actual
inverter interface type
3. Battery Terminals
F
AB C
Note
Left side
Front
No.
Description
No.
In the
A
SOC LED
Batterry
Package
B
STATUS LED
C
POWER SWITCH
D
LINK OUT
E
LINK IN
4. Installation Steps
RS485 ( Inverter side)
Please plug into the RS485
port of the inverter.
rter
rt
STEP-1:
Fix the pegboard on the wall and mark the position of the five holes
5
6
7
8
NC
NC
NC
RS485-A
with a marker.
CAN(lnverter side)
Please plug into the CAN
port of the lnverter.
5
6
7
8
CANH
NC
NC
NC
STEP-2:
Drill holes with electric drill, make sure the holes are deep enough
(at least 50mm) for installation, and then tighten the expansion
tubes.
D E F G H I
STEP-3:
Install the expansion tube in the hole and fix the pegboard with
Right side
self-tapping screws, then pre-lock the M5*70 screws on both
sides (pre-lock depth <15mm).
Description
F
PCS_1
G
PCS_2
H
Ground screw
I
POWER
Position
Suggested size
＜
Left
>300mm
Right
>300mm
Top
>300mm
Bottom
<100mm
STEP-4:
Hang the battery over the bracket, move the battery close to it,
lower the battery, and make sure the 2 mounting bars on the back
are fixed well with the 2 grooves on the bracket.
5. Wiring Steps
Wall mounting：
Standing mounting：
Note：junction box not included in the package and need
separate purchase.
M6
2.2~2.7
Inverter
junction box
Inverter
junction box