DSC WS4965 Installatie-instructies - Pagina 2

Blader online of download pdf Installatie-instructies voor {categorie_naam} DSC WS4965. DSC WS4965 2 pagina's. Trizone door/window contact

Pagina afdrukken

5. Mounting the WS4965

Mounting the WS4965 in Reed Switch Mode

• Place the mounting bracket in the position determined in the Enrolling, Pro-

gramming Placement step. Secure the bracket to the door frame using the two

screws provided. See Figure B.

• "Snap" the sensor in place.

• To release bracket: Remove the front cover. Push the tab (see Figure B) with a

small screwdriver and slide the WS4965 down.

• Align one end of the magnet with the notch on the side of WS4965 housing.

See Figure A.

• Mount the magnet a maximum of 1/2" (1.27cm) from the WS4965 using

the screws provided. If necessary use the spacers provided. See Figure C.

• Mount magnet: Open and close the door/window to ensure that there is no

interference.

Note: Only one magnet can be used for each WS4965. The contact shall

be installed so that a door or window cannot be opened more than 2

inches (51 mm) without causing an alarm condition.

Mounting the WS4965 in Tilt Switch Mode

Remove Jumper 3 (JP3) for "tilt switch" operation.

For the tilt switch to be in the closed position, mount the WS4965 in the vertical position, with the battery located on the bottom. Once the garage

door is open, the tilt switch will activate and generate a transmission. See Figure D.

The WS4965 can be programmed to wait 1 minute after the tilt switch activates before it transmits the alarm. This is useful for the garage doors

which require longer entry delay time. To program this feature, remove Jumper 2 (JP2).

Notes: The reed switch is deactivated when using the tilt function.

By carefully moving the tilt switch up or down, the degree of motion required to cause an alarm can be adjusted.

Do not permanently mount the WS4965 until the Placement Test has been successfully passed.

Note: This mode is not to be used in UL listed installations.

6. External Contacts: The WS4965 has 2 normally closed contact terminals. These can be used for additional hardwired wired contacts or other dry con-

tact switches. Connect the external devices to the contact terminals as per the manufacturers instructions. The maximum wire run from the external con-

tacts must not exceed 25ft (7.6m).

Note:For UL Installation, the external contacts and WS4965 must be in the same room.

7. Testing: Verify Sensor operation, Tamper operation and Supervisory Operation. Operation of these features is explained below.

WS4965 Operation:

• Tamper Switch: The WS4965 comes equipped with case tamper detection. If the cover is removed, the WS4965 will report a zone tamper to the

control panel. Upon tamper, all 3 serial numbers will report a tamper transmission.

• Supervision: The WS4965 sends a periodic supervisory transmission to the panel. If the panel fails to receive a transmission within the prepro-

grammed period (refer to receiver manual for supervisory window), it will indicate a fault on the keypad. All three serial numbers will transmit a

separate supervisory signal to the receiver.

• Low-Battery LED Indicator: There is a low-battery LED indicator on the WS4965. It will flash at 10 second intervals when a low battery con-

dition is detected and transmitted to panel. This will provide visual identification of the unit that requires a battery change.

• Battery Replacement: The WS4965 requires one CR123A lithium battery. To replace the battery, remove the cover by pressing on the end and

lifting it up. Use care when installing the battery and observe the correct polarity. Dispose of used battery promptly. Keep away from children. Do

not disassemble and do not dispose of in fire.

Caution: The battery used in this device may present a fire or chemical burn hazard if mistreated. Do not recharge, disassemble, heat above

100°C (212°F) or dispose of in fire. Replace battery with Panasonic CR123A only. Use of another battery may present a risk of fire or explosion.

WARNING!: Battery may explode if mistreated. Do not recharge, disassemble or dispose of in fire.

Shown with NO Spacer

Figure C

FCC ID: F5305WS4965

This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device must not cause harmful

interference, and (2) must accept any interference received, including interference that may cause undesired operation.

IC: 160A-WS4965 - The term "IC:" before the radio certification number only signifies that Industry Canada technical specifications were met.

Toronto, Canada • www.dsc.com

Technical Support:

1-800-387-3630 (Canada & US), 905-760-3036

Shown WITH Spacer

Push the tab

with screwdriver

Tab

Mounting Bracket

Figure B

TILT SWITCH

NOT MAKING

CONTACT

(Open)

Alarm

Figure D

29007111R002

Printed in Taiwan

MAGNET

1/2" (1.27 CM)

(1.27 CM)

MAX

TILT SWITCH

MAKING

CONTACT

(Normally Closed)

Restore