DSC CLASSIC PC1555 Gebruiksaanwijzing - Pagina 8

Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} DSC CLASSIC PC1555. DSC CLASSIC PC1555 11 pagina's.

Pagina afdrukken

NOTE: If you return and find that an alarm has occurred while you were away, it is possible that

an intruder may still be on the premises. Go to a neighbour's house, and call the local police to

investigate.

The alarm memory is cleared each time the panel is armed so that any alarms showing are

alarms that occurred only during the last armed period.

If An Alarm Sounds

Fire Alarm

If your system has been installed with fire detectors and the bell sounds in a pulsing mode, follow your

emergency evacuation plan immediately (see "Fire Escape Planning" on page 15).

Intrusion Alarm

If an intrusion alarm sounds, indicated by a continuous NMF-1008 buzzer, bell, siren, the alarm may

be silenced by entering your access code. If the alarm was unintentional, call local authorities

immediately to avoid an unnecessary response.

You can determine the source of the alarm by following the instructions in the "Disarming" section (see

page 5). Once the source of the alarm has been corrected, the panel can be restored to its original

Armed state.

Function Keys

Some keypad models have five function keys, located to the right of the number pad, which allow easy

single-button activation of the most commonly used features. If these keys have been enabled by your

installer , you can execute their programmed function by pressing and holding the corresponding key

for two seconds.

For information regarding the operation of the function keys, talk to your alarm installer.

Programming Security Codes

Programming codes from an LED Keypad:

The Master Code

To program the Master Code, enter [ ][5][current Master Code][40][new Master Code]. The Master

Code must be four digits unless otherwise indicated by your installer. Enter digits 0 through 9 only.

Press [#] to return to the Ready state.

Be sure to record your new Master Code on the "System Information" page in this booklet. NOTE: We

recommend that the factory default Master Code [1234] not be used.

Additional Codes

Up to 36 additional codes may be programmed. Codes 01-32 are regular access codes. Codes 33

and 34 are duress codes. Codes 41 and 42 are the system master codes.

To program a new code:

Enter [ ][5][Master code][code number][new access code]. The code number is a double-digit

number from 01-34 or 41-42.

Access codes must be four digits long. Enter digits 0 through 9 only.

To exit code programming, press [#].

will flash all 6 zone lights and will beep every second, to indicate that all zones have been bypassed.

When the passkey is removed, a 2-minute exit delay is initiated, during which the keypad will beep

three times every second. After the exit expires, the alarm will return to its normal armed state.

Viewing Trouble Conditions

The control panel continuously monitors a number of possible trouble conditions. If one of these trouble

conditions occur, the keypad will beep twice every 10 seconds until you press any key on the keypad.

NOTE: A TROUBLE condition reduces the security your system is designed to provide. Call your

installing company for service.

To view troubles from an LED Keypad:

A trouble will be indicated by the Trouble light which will remain ON until the trouble condition is cleared.

If you cannot determine or remedy the cause of the trouble condition, contact your installer for

assistance.

To view the type of trouble condition, press [ ][2]. One or more zone lights will turn ON, indicating the

various trouble conditions:

Zone Light Type of Trouble

1 ....... Service required. Call your installation company for service. Press [1] and one or more of

the zone lights corresponding to the following system troubles will turn ON:

........

1. Low Battery

........

2. Bell Circuit Trouble

........

3. General System Trouble

........

4. General System Tamper

2 ....... Indicates the loss of AC power. When this trouble occurs, the Trouble light will turn ON but

the keypad buzzer will not sound.

3 ....... Telephone line trouble.

4 ....... The panel has failed to communicate with the central station.

5 ....... Zone fault. Press [5] and the zone light(s) corresponding to the faulted zones will turn ON.

6 ....... Zone tamper. Press [6] and the zone light(s) corresponding to the tampered zones will turn ON.

7 ....... Low zone battery. This trouble is generated when a wireless device exhibits a low

battery condition.

Press [7] one, two, or three times to view which devices are experiencing battery failure.

The following will occur:

Keypad Beeps Keypad Display

Press [7] ........... 1 .......... Zones with low batteries (LED keypad - zone lights 1 to 8)

Press [7] again .. 2 .......... Handheld keypads with low batteries (LED keypad - zone lights 1 to

Press [7] again .. 3 .......... Wireless keys with low batteries (LED keypad - zone lights 1 to

8). To view the battery conditions of wireless keys 9 through 16, you

must be at an LCD keypad.

5. General System Supervisory