DSC LE4000 Installatiehandleiding - Pagina 7
Blader online of download pdf Installatiehandleiding voor {categorie_naam} DSC LE4000. DSC LE4000 8 pagina's. Lte wireless alarm communicator
Pagina afdrukken
MODIFICATION STATEMENT
Digital Security Controls has not approved any changes or modifications to this device by the user.
Any changes or modifications could void the user's authority to operate the equipment.
Digital Security Controls n'approuve aucune modification apportée à l'appareil par l'utilisateur,
quelle qu'en soit la nature. Tout changement ou modification peuvent annuler le droit d'utilisation de
l'appareil par l'utilisateur.
INTERFERENCE STATEMENT
This device complies with Part 15 of the FCC Rules and ISED Canada licence-exempt RSS stand-
ard(s). Operation is subject to the following two conditions: (1) this device may not cause inter-
ference, and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'ISED Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radi-
oélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
WIRELESS NOTICE
This equipment complies with FCC and ISED Canada radiation exposure limits set forth for an
uncontrolled environment. The antenna should be installed and operated with minimum distance of
20 cm between the radiator and your body. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Cet appareil est conforme aux limites d'exposition aux rayonnements de la ISED Canada pour un
environnement non contrôlé. L'antenne doit être installé de façon à garder une distance minimale
de 20 centimètres entre la source de rayonnements et votre corps. L'émetteur ne doit pas être
colocalisé ni fonctionner conjointement avec à autre antenne ou autre émetteur.
Antenna gain must be below/Gain de l'antenne doit être ci-dessous:
Frequency Band/Bande de fréquence
GSM 850 / FDD V
PCS 1900 / FDD II
LTE B2
LTE B4
LTE B5/ B12/ B13
FCC CLASS B DIGITAL DEVICE NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pur-
suant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful inter-
ference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following meas-
ures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is con-
nected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC ID:F5317LE4000
LE4000 Product Identifier US: F5317MO00ALE4000
REN: 0.0A
USOC Jack: RJ-31X
WARNING: To satisfy FCC RF exposure requirements for mobile transmitting devices, a
separation distance of 20cm or more must be maintained between the antenna of this
device and persons during device operation.
Telephone Connection Requirements
A plug and jack used to connect this equipment to the premises wiring and telephone network must
comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant
telephone cord and modular plug is provided with this product. It is designed to be connected to a
compatible modular jack that is also compliant. See installation instructions for details.
Ringer Equivalence Number (REN)
The REN is used to determine the number of devices that may be connected to a telephone line.
Excessive RENs on a telephone line may result in the devices not ringing in response to an incom-
ing call.
In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the num-
ber of devices that may be connected to a line, as determined by the total RENs, contact the local
Telephone Company. For products approved after July 23, 2001, the REN for this product is part of
the product identifier that has the format. US: AAAEQ##TXXXX. The digits represented by ## are
the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is sep-
arately shown on the label.
Incidence of Harm
If this equipment LE4000 causes harm to the telephone network, the telephone company will notify
you in advance that temporary discontinuance of service may be required. But if advance notice is
not practical, the Telephone Company will notify the customer as soon as possible. Also, you will be
advised of your right to file a complaint with the FCC if you believe it is necessary.
Changes in Telephone Company Equipment or Facilities
The Telephone Company may make changes in its facilities, equipment, operations or procedures
that could affect the operation of the equipment. If this happens the Telephone Company will
provide advance notice in order for you to make necessary modifications to maintain uninterrupted
service.
Equipment Maintenance Facility
If trouble is experienced with this equipment for repair or warranty information, please contact the
facility indicated below. If the equipment is causing harm to the telephone network, the Telephone
Company may request that you disconnect the equipment until the problem is solved. This equip-
ment is of a type that is not intended to be repaired by the end user.
DSC c/o APL Logistics, 757 Douglas Hill Rd., Lithia Springs, GA 30122
Additional Information
Connection to party line service is subject to state tariffs. Contact the state public utility com-
mission, public service commission or corporation commission for information. Alarm dialling equip-
ment must be able to seize the telephone line and place a call in an emergency situation. It must be
able to do this even if other equipment (telephone, answering system, computer modem, etc.)
already has the telephone line in use. To do so, alarm dialling equipment must be connected to a
properly installed RJ-31X jack that is electrically in series with and ahead of all other equipment
attached to the same telephone line. Proper installation is depicted in the figure below. If you have
any questions concerning these instructions, you should consult your telephone company or a qual-
ified installer about installing the RJ-31X jack and alarm dialling equipment for you.
LE4000
6.21 dBi
Industry Canada Compliance Statement
3.76 dBi
This Equipment meets the applicable Industrial, Scientific and Economic Development (ISED)
Canada Terminal Equipment Technical Specifications. This is confirmed by the registration num-
2.76 dBi
ber. The abbreviation, IC, before the registration number signifies that registration was performed
based on a Declaration of Conformity indicating that ISED Canada technical specifications were
2.82 dBi
met. It does not imply that that ISED Canada approved the equipment. The Ringer Equivalence
Number (REN) for this terminal equipment is 0.0. The REN assigned to each terminal equipment
2.45 dBi
provides an indication of the maximum number of terminals allowed to be connected to a telephone
interface. The termination on an interface may consist of any combination of devices subject only
to the requirement that the sum of the Ringer Equivalence Numbers of all devices does not exceed
5.
IC:160A-LE4000
Cet équipement est conforme aux spécifications techniques applicables aux équipements ter-
minaux d'ISED Canada. Ceci est confirmé par le numéro d'enregistrement. L'abréviation IC
précédant le numéro d'enregistrement signifie que l'enregistrement a été effectué sur la base de la
Déclaration de conformité indiquant que le produit est conforme aux spécifications techniques
d'ISED Canada. Ceci n'implique pas que le produit ait été approuvé par ISED Canada.
Le nombre équivalent de sonneries (REN) de cet appareil terminal est 0.0. Le REN attribué à
chaque équipement terminal fournit une indication sur le nombre maximum de terminaux pouvant
être connectés sur une interface téléphonique. La terminaison sur une interface peut constituer en
n'importe quelle combinaison d'appareils, à la condition seulement que la somme des Nombres équi-
valents de sonneries de tous les appareils ne soit pas supérieure à 5.
CAN ICES-3 (B) / NMB-3 (B)
The term "IC:" before the radio certification number only signifies that ISED Canada technical spe-
cifications were met.
NISTValidation of encryption algorithm AES128 (certificate No. 5011 available at NISTwebsite).