Attwood Pulsar 5045 Installatie-instructies - Pagina 2

Blader online of download pdf Installatie-instructies voor {categorie_naam} Attwood Pulsar 5045. Attwood Pulsar 5045 2 pagina's. Attwood 12-volt navigation light installation instructions

INSTALLATION, RAISED BASE MOUNT
All-Round Lights
1. Place light in position as shown in Figure 1.
Important: Before drilling, be sure that light will shine within 5 of
horizontal when boat is floating.
2. Mark and drill 3/8" (10mm) diameter hole (Figure 4; Sidelight lens
is shown).
3. Thread wire leads and base stem into hole. Mark location of screw
holes. Proceed to Step 4 below.
Bi-Color Sidelights and Sidelight Pairs
1. Place sidelight(s) in position as shown in Figure 2.
Important: Before drilling, be sure that sidelights will shine straight
ahead and within 5 of horizontal when boat is floating.
2. For Bi-Color Combination light, mark and drill 3/8" (10mm) diameter
hole on the boat centerline. For Sidelight Pairs, mark and drill 3/8"
(10mm) diameter hole on each side deck of the boat, equal distance
from the bow. (Figure 4)
3. Thread wire leads and base stem into hole. Align lens division with
straight-ahead position and mark location of screw holes.
4. Remove base and drill 1/8" (3mm) pilot holes for both screws.
5. Bring 12V DC (+) and (-) wires up through deck hole. Connect wires
using waterproof crimp on butt joint connectors.
6. Activate light to verify proper operation.
7. Apply non-silicone sealant to underside of base.
8. Align and fasten base with stainless screws. Do not over tighten.
(Figure 4)
Figure 4
Notch
On
Off
Lens Helmet
"O" Ring
3/8" (10mm)
Dia. Hole
1/8" (3mm)
Pilot Holes
FINAL WIRING
CAUTION:
Power source must be positive 12V DC only. All positive (+12V DC)
wires must be fused to protect the circuit. Attwood Pulsar Navigation
Lights require a 1-amp fuse. Failure to make proper connections and
fusing will void product warranty.
1. Neatly thread wires to dash avoiding any areas where abrasion or
snagging may occur.
2. Use waterproof crimp on butt joint connectors to attach wires to a
switch on the dash that allows for two-position operation - one for
running lights and one for anchor lights. Test lights for proper
operation. (Figure 5)
Figure 5
3-Way Switch
1-Amp Fuse
MAIINTENANCE
For cleaning or to replace bulb, gently twist lens helmet counter clock-wise
to remove. Replace with standard #906 lamp, Attwood #9235. Check"O"-ring
for cracks and insure that it is properly positioned on lens. Replace lens
helmet on base and turn clockwise until click is heard and felt.
ATTWOOD LIMITED WARRANTY
ATTWOOD CORPORATION, 1016 North Monroe, Lowell, Michigan 49331
("Attwood") warrants to the original consumer purchaser that Attwood
brand products will be free from defects in materials and workmanship
under normal use and service for one year from the date of original consumer
purchases. This limited warranty is not applicable if the product has been
damaged by accident, improper installation, unreasonable or improper
use, lack of proper maintenance, unauthorized repairs or modifications,
normal wear and tear, or other causes not arising out of defects in materials
or workmanship. Attwood products are warranted for use on pleasure boats.
Any other use - including but not limited to commercial, racing, or non-marine
use - are not covered under this warranty. Attwood's obligation under this
warranty is limited to repair of the product at Attwood's plant or replacement
of the products at Attwood's option without expense to the original consumer
purchaser. Any expenses involved in the removal, reinstallation or
transportation of the product are not covered by this warranty. The product
must be returned to Attwood's plant at the address above, postage prepaid,
and insured with proof of original purchase including date. If Attwood is
unable to replace the product and repair is not commercially practical or
cannot be timely made, or if the original consumer purchaser is willing to
accept a refund in lieu of repair or replacement, Attwood may refund the
purchase price, less an amount for depreciation. The acceptance by
Attwood of any product returned or any refund provided by Attwood shall
not be deemed an admission that the product is defective or in violation
of any warranty. Products that are replaced or for which a refund is
issued become the property of Attwood.
THIS WARRANTY IS ATTWOOD'S ONLY EXPRESS WARRANTY OF
THIS PRODUCT. NO IMPLIED WARRANTY SHALL EXTEND BEYOND
ONE (1) YEAR FROM THE DATE OF ORIGINAL CONSUMER PUR-CHASE.
ATTWOOD SHALL NOT BE LIABLE FOR ANY DAMAGES FOR LOSS
OF USE OF THIS PRODUCT, NOR FOR ANY OTHER INCIDENTAL OR
CONSEQUENTIAL DAMAGES, COSTS OR EXPENSES.
Some states do not allow limitations on how long an implied warranty
lasts or the exclusion or limitation of incidental or consequential damages,
so the above limitations and exclusions may not apply to you. This warranty
gives you specific legal rights, and you may have other rights which vary
from state to state.
© 2003 Attwood Corporation
1016 N. Monroe Street, Lowell, MI 49331-0260 www.attwoodmarine.com
Pos. (+)
Neg. (-)
12V DC