Attwood 66510 Installatie-instructies - Pagina 2

Blader online of download pdf Installatie-instructies voor {categorie_naam} Attwood 66510. Attwood 66510 2 pagina's. 4" and 6" flush mounted cleat
Ook voor Attwood 66510: Installatie-instructies (1 pagina's)

Pagina afdrukken

OPTIONAL WATER RECEPTACLE INSTALLATION. (Water receptacle sold

separately.) If using the water receptacle on:

Thru-Bolt Version

The same cut-out can be used when the cleat is mounted with the receptacle.

1. Place water receptacle on underside of cleat and attach per flush cleat installation

instructions (Figure 3). The screws used must be long enough to go through the

flange of the cleat, deck, mounting plate and then the water receptacle.

2. Connect 3/8" inner diameter hose to the fitting on the receptacle. Route the hose into

the bilge or to a drain fitting.

Figure

•

Hose

Fitting

ATTWOOD LIMITED WARRANTY

This limited warranty is not applicable if the product has been damaged by accident,

improper installation, unreasonable or improper use, lack of proper maintenance,

unauthorized repairs or modifications, normal wear and tear, or other causes not

arising out of defects in materials or workmanship.

Attwood products are warranted for use on pleasure boats. Any other use — including

but not limited to commercial, racing, or non-marine use — are not covered under this

warranty. Attwood's obligation under this warranty is limited to repair of the product at

Attwood's plant or replacement of the products at Attwood's option without expense

to the original consumer purchaser. Any expenses involved in the removal, reinstallation

or transportation of the product are not covered by this warranty.

The product must be returned to Attwood's plant at the address above, postage prepaid,

and insured with proof of original purchase including date.

•

Machine

Screws

•

Thru-Bolt Flush

Cleat

Tension/

•

Travel

Adjustmen

t Set

Screw

•

Cut-Out Hole

•

Marine Sealant

•

Backing

Plate

Wate

•

Receptacl

(Sold

Separately)

•

Lock

•

Washer Nut

Studded

Version

1. After the cleat has been installed, attach water receptacle to the backing plate using

(4) #8 self-tapping screws (Figure 4).

2. Connect 3/8" inner diameter hose to the fitting on the water receptacle. Route hose

into bilge or to a drain fitting.

Figure

Hose

Fitting

MAINTENANC

• A silicone based lubricant maybe used on cleat shafts to increase the ease of

travel.

If Attwood is unable to replace the product and repair is not commercially practical or

cannot be timely made, or if the original consumer purchaser is willing to accept a refund

in lieu of repair or replacement, Attwood may refund the purchase price, less an amount

for depreciation. The acceptance by Attwood of any product returned or any refund

provided by Attwood shall not be deemed an admission that the product is defective

or in violation of any warranty. Products that are replaced or for which a refund is

issued become the property of Attwood.

THIS WARRANTY IS ATTWOOD'S ONLY EXPRESS WARRANTY OF THIS

PRODUCT. NO IMPLIED WARRANTY SHALL EXTEND BEYOND ONE (1) YEAR

FROM THE DATE OF ORIGINAL CONSUMER PURCHASE. ATTWOOD SHALL NOT

BE LIABLE FOR ANY DAMAGES FOR LOSS OF USE OF THIS PRODUCT, NOR FOR

ANY OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES, COSTS OR

EXPENSES.

Some states do not allow limitations on how long an implied warranty lasts or the

exclusion or limitation of incidental or consequential damages, so the above limitations

and exclusions may not apply to you. This warranty gives you specific legal rights, and

you may have other rights which vary from state to state.

Discover other anchors & docking on our website.

•

Studded Flush

Cleat

•

Studs

Cut-Out

•

Hole

•

Marine

Sealant

•