Auber SWA-2451A Gebruiksaanwijzing - Pagina 2

Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Auber SWA-2451A. Auber SWA-2451A 6 pagina's. Pid temperature controller

Pagina afdrukken

AUBER INSTRUMENTS

contact and other may need N.C. contact switch. Please see Fig. 7 and 9 for

examples.

3.3 Control output connection

The SSR control output of the controller SWA-2451A provides a pulsed 12V DC

signal for the SSR. Connect terminal 10 to the positive input and terminal 9 to

the negative input of the SSR. See Figure 7 for details.

3.4 For first time users without prior experience with PID controllers, the

following notes may prevent you from making common mistakes.

3.4.1 SSR output power does not come from the input of the SSR. The output

of the SSR is a single pole switch between terminals 1 and 2 of the SSR. The

input of the SSR is for controlling, or triggering the SSR. (Please note we are

talking about the SSR itself, not the SSR control output of the controller).

When switching a North American 240V AC power (2 hot wires), the heater will

be live even when the SSR is off. Users should install a double pole mechanical

switch to the power input, to cut both hot wires at same time when not in use.

3.4.2. For all controller models listed in this manual, the power is controlled by

regulating the duration of on time for a fixed period of time. It is not controlled by

regulating amplitude of the voltage or current. This is often referred as time

proportional control. For example, if the cycle rate is set for 100 seconds, a

60% output means controller will switch on the power for 60 seconds and off for

40 seconds (60/100 = 60%). Almost all high power control systems use time

proportional control because amplitude proportional control is too expensive

and inefficient.

4. Front Panel and Operation

Figure 2. Front panel.

PV display: Indicates the sensor read out, or process value (PV).

SV display: Indicates the time when timer is used. If timer is deactivated, it

indicates the set temperature (SV). In manual control mode, an "H" is

displayed on the most left digit to indicate number is for percentage of

output (%).

Output indicator: It is synchronized with SSR output on the controller

(terminal 9 and 10). When it is on, SSR output is triggered, and your

external SSR & heater (or cooler) are powered.

AL1 indicator: It is synchronized with alarm 1 relay (AL1). When timer is on,

it works as the timer relay output indicator. When timer is deactivated, it

lights when Alarm 1 condition meets.

AL2 indicator: It is synchronized with alarm 2 relay (AL2). It lights when

Alarm 2 condition meets.

Auto-tune indicator: It lights up when auto-tune starts.

SET key: Press and hold this key for 3 seconds will enter the temperature

control parameter setting mode. When the controller is in temperature, or

timer parameter setting mode, press this key momentarily will lead the

display to the next parameter.

Automatic/Manual function key/Data shift key ◄: press ◄ for 3 seconds to

enter manual tuning mode. Press ◄ for 3 seconds again to exit.

Decrement key ▼: Decreases numeric value of the setting value. Press for

3 seconds to enter the timer setting mode.

2019.01

10. Increment key ▲: Increases numeric value of the setting value. Press for 3

seconds to enter the temperature setting mode.

4.1 Display Modes

Display mode 1: Normal operation display.

PV is the abbreviation for Process Value. SV is the abbreviation for Set Value.

When the power is turned on, the upper display window shows the measured

temperature value. If the timer is used, the lower window shows set timer value.

When timer starts, it shows the time as it counts up or down. If the timer is

disabled (INT = 0), the lower display shows the set temperature.

Display mode 2: Changing temperature set value (SV)

Press the ▲key for 3 seconds, and then release it. The decimal point on the

lower right corner will start to flash. Press the ▼or ▲ key to change SV until

the desired value is displayed. If the change of SV is large, press the ◄ key to

move the flashing decimal point to the desired digit that needs to be changed.

Then press the ▼or ▲key to start changing SV from that digit. The decimal

point will stop flashing after no key is pressed for 3 seconds. The changed SV

will be automatically registered without pressing the SET key.

Display mode 3: Timer parameter set up.

Press the ▼ key for 3 seconds to change the display status into timer

parameter setting mode. The upper display window shows the timer parameter

symbol to be changed, the lower display shows its value. Press the ◄, ▼or ▲

to change the setting. Then, press SET to go to next parameter. If no key is

pressed for 10 seconds, the display will return to mode 1 automatically. The

change of value will take effect without the need for pressing the SET key. See

4.14 to 4.16 for more details.

Display mode 4: Manual mode.

Press the ◄ key for 3 seconds to enter the manual mode. In this mode, the

lower display has an H on the most left. The number on the right is the

percentage of power output. Press the ▼or ▲ to adjust the power. Press the

◄ key for 3 seconds again to exit this mode. For more details, please see 4.3.

Display mode 5: Temperature control parameter setting.

Press the SET key for 3 seconds to enter the temperature control parameter

setting mode. The upper display window shows the parameter symbol to be

changed, the lower display shows its value. Press ◄, ▼or ▲ to change the

setting. Then, press SET to go to next parameter. If no key is pressed for 10

seconds, the display will return to mode 1 automatically. The change of value

WWW.AUBERINS.COM

P2/6