CON-TEC DLUX micro power 80 Gebruiksaanwijzing

Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} CON-TEC DLUX micro power 80. CON-TEC DLUX micro power 80 2 pagina's. Bike led battery light set

Pagina afdrukken
Instruction manual bike
LED battery light set
DLUX micro power 80
DLUX micro power 120
Scope of delivery
• handlebar bracket
• battery front light with
• insert for Ø 25-30mm
lamp head (changeable)
• insert for Ø 30-35mm
adapter cable USB-C to USB-A
adapter cable micro USB to USB-A
General notes
Proper use
The product is intended for use on bicycles with pedal assistance and serves the illumination of the road.
This LED front light is approved according to the currently valid RTLR (StVZO). The product is intended for
outdoor use.
Safety instructions
- Do not look into the light.
- Do not point the light directly at people or animals.
- The light beam of the LED front light must point straight in direction and may not blind other road users.
- The light distribution may be obscured by no other attached parts or pieces of luggage, not even partially.
- The LEDs are not interchangeable. If the LED fails, the entire luminaire must be replaced.
WARNING! LIFE AND ACCIDENT HAZARD FOR INFANTS AND CHILDREN!
Never leave children unattended with the packaging material, because of suffocation danger by
swallowing packaging parts. Always keep the device away from children. The device is not a toy! This
device can be used by children of age 8 and over and by persons with reduced physical or mental
capabilities or lack of experience and knowledge if they have been supervised or instructed concerning
the safe use of the device and by understanding resulting hazards. Children are not allowed to play with
the device. Cleaning and user maintenance should not be carried out by children without supervision.
Do not disassemble the device. Improper repairs can cause significant risks for the user. Only have
repairing made by qualified personnel.
Manual_DLUX micro power 80/120
Assembly / disassembly
Handlebar bracket
Preparation: select suitable insert (Ø 25-30mm or Ø 30-35mm) on
the basis of the given handlebar size and insert into the
handlebar clamp
Place clamp around handlebar and hook in grip nut Tighten the
handle nut
Front Light
Assembly
2.
1. Put on the front headlight on rear edge of bracket
2. Press down until the front headlight engages in
the clamp bracket
• battery rear light
• mounting clip
• rubber straps
Alignment
Align the LED front light so that the light beam reaches the road approx. 10 meters in front of the wheel (see ill.). The
light beam of the LED front light must point straight in direction from 400 up to 1200mm.
Centering
Attention!
Check regularly the correct setting of your front light.
Disassembly
2.
1.
1.
1. Press release button on underside and
remove front headlamp (2.)
Inclination
Operation
Switch on/off
To switch on and off, press and hold the button for 2 seconds each time.
Brightness levels
The front headlight has 4 selectable brightness level. The activation of the next brighter
level is achieved by a short push of the button. The highest brightness level is followed
by the lowest brightness level again.
Display battery status / brightness levels
100 %
75 %
50 %
25 %
The status displays go out automatically after 10 seconds and are
reactivated the next time the key is pressed.
Level 1
Level 2
Level 3
Version
20 Lux
40 Lux
60 Lux
80Lux
20 Lux
40 Lux
80 Lux
120Lux
Low battery mode
From a remaining battery capacity of 4%, the front headlight limits the brightness to level 1. The
lowest LED of the battery status indicator flashes red.
Temperature monitoring
If the lamp head overheats, the front light limits the brightness to level 1 until the normal operating
temperature is reached again.
Powerbank function
The front headlight can be used to charge mobile USB devices.
Charging starts automatically as soon as a USB device is plugged into
the USB-C socket. The function is not available in low battery mode.
Charging
The internal battery of the front headlight is charged via a USB voltage
source. The supplied adapter cable is plugged into the USB-C socket.
The current state of charge is displayed during charging.
4
3
2
1
Level 4
80 Lux
120 Lux
USB-C socket