Elite Acoustics Engineering A2-5 Handmatig - Pagina 7

Blader online of download pdf Handmatig voor {categorie_naam} Elite Acoustics Engineering A2-5. Elite Acoustics Engineering A2-5 11 pagina's. Acoustic amplifier with 4 channels, mixer, effects, battery powered and bluetooth
Ook voor Elite Acoustics Engineering A2-5: Beknopte handleiding Handboek (5 pagina's)

Pagina afdrukken
Elite Acoustics Engineering A2-5 Handmatig
Charge Only
INSTR
20
10
50
60
Gain
Mute
EFX/AUX
Send Level
EFX
AUX
PAD
Instrument
+48V
Power
On
Battery Switch
Connect
Off
E L I T E
A C O U S T I C S
www.EliteAcoustics.com
High – used to add sibilance and crispness to your sound, with the knob at 12:00, there is no
boost or cut to the high frequency content.
Mid – Helps control the clarity of your overall mix and should be adjusted to suit lower or
higher volume performance levels. Boosting the mids helps speech clarity and intelligibility at
lower volumes while cutting the mids produces a more natural sound at higher volumes. The
Mid frequency selection knob allows for a range extending from high LF to low HF. When set
to 12:00 the Mid frequency peak is around 1.2k Hz, with +/- 12dB of boost or cut depending
on the setting of the Mid knob. Here again, with Mid set to 12:00 the mid control is effectively
out of the circuit.
Low – In general, lower volumes can benefit from LF boost to help bring out the bass at
these lower settings, but it is usually left flat or even slightly cut for high playback levels.
Notch – When it comes to the mechanics, Notch filtering is very much like the adjustable
mid frequency described above. However, the frequency range is much lower, and the filter
itself is much tighter, hence the term "notch." When used in "cut" mode, this is very effective
in managing feedback, which is explained in some detail in our Feedback section. However,
the notch can be set to cut or boost to allow for the full range of possibilities. Many times
feedback is not an issue, and the artist can take advantage of a particular notch setting to
effectively tweak a final mix to accommodate specific room or instrumentation considerations.
Phase – Use the phase setting that best supports your overall sound and system integration
considerations. For example, Phase can be set to facilitate the best bass response at low
volumes, and it can also be effective as a feedback deterrent, which will be reviewed in our
Feedback section.
5
CONNECTING TO ANOTHER SPEAKER
CHAN 1
CHAN 2
CHAN 3/4
-10
+10
-10
+10
-10
10
50
30
Level
Notch Filter
High
Gain
Mute
EFX Level
100
450
-10
+10
Frequency
Mid
EFX/AUX
Send Level
250
5k
Mid Frequency
Phase
EFX
AUX
PAD
Right
-10
+10
Low
Instr
Mic/Line
Line
Monitor
Right Output
Line
Mic 1
Mic 2
3
2
1
Low
DC INPUT
Disconnect
Serial Number
Designed, Assembled, & Tested
in California, USA
For Maximum Battery Life
- Recharge after every use
- Use & recharge battery at least once a month
- Do not leave power switch in the "ON"
position when it is not in use
- Keep unit in a cool, dry place away from extreme
temperatures
- Do not service, modify, or replace the battery
- If the battery fails to charge, contact Elite Acoustics
Battery Switch
- Connect - to enable battery power
- Disconnect - to disable battery power
WARNING
Only exchange the original speaker system
battery
with
a
genuine
Elite
Engineering
replacement.
Elite
Engineering cannot guarantee the safety and
compatibility
of
batteries
from
manufactures for the use in operating the speaker
system. Use of an uncertified battery may void all
warranties.
ABOUT EQ AND PHASE SETTINGS
TIP - EFX Bypass
Footswitch
AUX Send
AUX Return
Main Outputs
CHAN 1/2
Direct Output
Output Level
Charge
The Monitor Right Output allows you to add
a second active monitor while preserving the
stereo image. The Monitor unit will play the
Left Channel content and the extension monitor
will play the Right Channel. If stereo imaging
is not desired, simply engage the Mono button
on the A2's top panel. Note that the Monitor
Acoustics
Acoustics
other
Right Output will not drive a passive speaker; it
is a Line-level output that can drive amplifiers
or active monitor systems.
Charge Only
CHAN 1
CHAN 2
INSTR
20
10
50
60
-10
+10
-10
+10
-10
10
50
Gain
Notch Filter
High
Gain
Mute
Mute
100
450
-10
+10
Frequency
Mid
EFX/AUX
EFX/AUX
Send Level
Send Level
250
5k
Mid Frequency
EFX
AUX
Phase
EFX
PAD
PAD
-10
+10
Low
Instr
Mic/Line
Line
Instrument
Line
Mic 1
Mic 2
TIP - EFX Bypass
CHAN 3/4
Footswitch
30
Level
EFX Level
AUX Send
AUX Return
AUX
Main Outputs
CHAN 1/2
Direct Output
Right
Monitor
Output Level
Right Output
Right