Anzzi FR-AZ273 Installatiehandleiding - Pagina 2

Blader online of download pdf Installatiehandleiding voor {categorie_naam} Anzzi FR-AZ273. Anzzi FR-AZ273 2 pagina's.

Pagina afdrukken

1
2

Ｓｔｅｐ　１

Ｈａｎｄｌｅ　ｉｎｓｔａｌｌａｔｉｏｎ

Place the base of the handle ﬂange kit

1

on the left hole. Insert the braided ﬂex

connectors through the hole.

From underneath, place metal washer

2

and locknut on each threaded stud and

tighten gently by hand.

3

Now, position and properly align the

handle on top. Tighten the locknuts with

a ﬂat head screwdriver or appropriate

tool. Do not overtighten.

Ｓｔｅｐ　２

Ｓｐｏｕｔ　ｉｎｓｔａｌｌａｔｉｏｎ

1

Unscrew the Allen screw in back of

the spout. Pull apart the spout from its

connector (do not unscrew). Separate

the spout ﬂange from the spout. Place

o-ring underneath the spout ﬂange and

place the ﬂange over the center hole

between the handle and hand shower.

Unscrew the superior spout locknut of

2

the spout connector. Make sure that the

locknut and the metal and rubber

washers are in place on the spout

connector. From underneath the

bathtub, insert the top of the

connector in the hole between the

handle and hand shower. From over

the bathtub, screw the superior spout

locknut to secure the connector and the

ﬂange in place.

3

Install the spout on the connector and

align the spout with the ﬂange, making

sure to insert the anti-rotation pin in

the stop hole. Tighten spout in place by

screwing the Allen screw in front of

the spout.

Ｓｔｅｐ　３　

Ｈａｎｄ　ｓｈｏｗｅｒ　ｈｏｌｄｅｒ　ｉｎｓｔａｌｌａｔｉｏｎ

1

Unscrew the locknut and take off metal

and rubber washers.

2

Insert the hand shower holder in the

hole making sure to place the o-ring

underneath the ﬁx holder. From under,

screw the rubber and metal washers,

as well as the retainer ring to the holder

in place.

Connect the hose to the hand shower

3

hole, making sure that the

rubber washer is in place.

From above, slide the hose through the

holder to sit the hand shower on its

base.

ill. A

ill. B

Ｓｔｅｐ　４

Ｖａｌｖｅ　ａｎｄ　ｗａｔｅｒ　ｓｕｐｐｌｙ　ｃｏｎｎｅｃｔｉｏｎ

1

Using the ﬂexible connectors included

(5), connect the valve to the spout

connector. Use the extra ﬂexible

connector (14) to join the spout to the

hand shower hose.Tighten using

appropriate tool. (ill. A)

Connect hot and cold valves to the

2

corresponding water supply lines using

ﬂexible connectors and tighten. (ill.B)

Ｓｔｅｐ　５

Ｔｅｓｔｉｎｇ　ｃｏｎｎｅｃｔｉｏｎｓ

WARNING: Remove aerator before

testing connections. Place the

appropriate wrench on the ﬂat edges

and unfasten. Use a cloth to not

damage the part. Do not overtighten.

1

Verify that there are no leaks by slowly

opening the hot and cold water. In case

of a leak, shut off the water supply and

tighten connectors 1⁄4 turn using the

appropriate tool. Repeat if necessary.

2

Turn on the faucet and leave both hot

and cold water running for at least one

minute to evacuate the air trapped in

the pipes. Turn off water.

3

Assemble the aerator as illustrated and

insert into the spout, tightening by hand.

You can now turn on water supply.

1
2