Casio 1361 Algemene handleiding - Pagina 3
Blader online of download pdf Algemene handleiding voor {categorie_naam} Casio 1361. Casio 1361 3 pagina's. Module
Pagina afdrukkenTo delete a specific Schedule Memo item
1. In the Schedule Memo Mode, use B or D to scroll through the data items and
display the one you want to delete.
2. Press A and the month digits begin to flash because they are selected.
3. Press B and D at the same time. The watch beeps and the message "
appears on the display, indicating that the item is deleted. At this time, the cursor
appear on the display, ready for input.
4. Input data or press A to return to the normal Schedule Memo Mode (the flashing
stops).
ALARM MODE
When the Daily Alarm is switched on, the alarm sounds for 20 seconds at the preset
time each day. Press any button to stop the alarm after it starts to sound. When the
Hourly Time Signal is switched on, the watch beeps every hour on the hour.
Note that the Daily Alarm and the Hourly Time Signal operate based on the digital time
setting.
To set the alarm time
1. Make sure that the watch is in the Alarm Mode. If
Alarm on indicator
not, use C to enter the Alarm Mode.
2. Hold down A while in the Alarm Mode until the
A
B
ON/OFF
hour digits start to flash on the display. The hour
digits flash because they are selected . At this
time the Daily Alarm is switched on automatically.
C
D
Hourly Time Signal on
indicator
Mode
Hour
Minutes
indicator
3. Press C to change the selection in the following sequence.
Hour
4. Press D to increase the selected digits and B to decrease them. Holding down
either button changes the number at high speed.
• The format (12-hour and 24-hour) of the alarm time matches the format you select
for normal timekeeping.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning or afternoon (indicated as "
5. After you set the alarm time, press A to return to the normal Alarm Mode (the
flashing stops).
The following shows how the display automatically changes if you do not operate any
button for a few minutes while in the Alarm Mode.
Alarm time setting
A few
(Flashing)
minutes
To switch the Daily Alarm and Hourly Time Signal on and off
Press B while in the normal Alarm Mode (when no digit is flashing) to change the
status of the Daily Alarm and Hourly Time Signal in the following sequence.
Both on
Both off
To stop the alarm
Press any button to stop the alarm after it starts to sound.
To test the alarm and select an alarm tone
1. Hold down D while in the normal Alarm Mode to sound the alarm.
2. While holding down D, press B to switch between the three available alarm tones.
The last alarm tone that is sounding is selected when you release D.
STOPWATCH MODE
Mode indicator
The Stopwatch Mode lets you measure elapsed time,
split times, and two finishes. The range of the stop-
watch is 23 hours, 59 minutes, 59.99 seconds.
SPLIT/RESET
A
B
To measure elapsed time
1. Press D to start the stopwatch.
2. Press D to stop the stopwatch.
C
D
• You can resume the measurement operation by
START/STOP
pressing D again.
3. Press B to clear the stopwatch to all zeros.
Hours
1/100 second
Minutes
Seconds
To record split times
1. Press D to start the stopwatch.
2. Press B to display the timing up to that point. Stopwatch timing continues internally.
• At this time, the display also changes from "
split time is being recorded.
• Split time is cleared if you exit the Stopwatch Mode during the timing operation.
3. Press B to clear the split time and to continue time measurement on the display.
• You can repeat steps 2 and 3 as many times as you want.
4. Press D to stop the time measurement.
5. Press B to clear the stopwatch to all zeros.
Minutes
" on the display).
Normal Alarm Mode
Timekeeping
A few
(No flashing)
Mode
minutes
Daily Alarm
Hourly Time
only
Signal only
" to "
", indicating that the
To time first and second place finishes
1. Press D to start the stopwatch.
2. Press B when the first finisher crosses the line, and record the time.
3. Press D when the second finisher crosses the line.
4. Press B to display the finishing time of the second finisher.
"
5. Press B again to clear the stopwatch to all zeros.
Hour hand
Minute hand
A
C
Current time
Mode
Current date
indicator
3. Press D to advance the hands of the analog timepiece.
4. After you set the analog time, press A to return to the normal Hand Setting Mode
(the flashing stops).
• The following shows how the display automatically changes if you do not operate
any button for a few minutes while in the Hand Setting Mode.
Hand time setting
(the indicator flashes)
ABOUT THE MODULE 1361 DISPLAY
The following shows how the display of module 1361 changes for about 20 seconds
when a Reminder signal sounds.
Normal display
• The display changes similarly when a Schedule Memo signal sounds, or when a
daily alarm sounds in the Timekeeping Mode. When a Schedule Memo signal
sounds, time of the nearest scheduled appointment appears, instead of the current
time.
The Auto Display function of this watch continually changes the contents of the digital
display. Note that you cannot use any of the watch's other function while the Auto
Display function is operating.
A
C
Note
The Auto Display function cannot be performed while you are making settings (i.e.
while digits or other settings are flashing on the display).
HAND SETTING MODE
When the time shown on the display does not match
the analog setting, use this mode to correct this situa-
tion by changing the analog setting.
B
To set the analog time
1. Make sure that the watch is in the Hand Setting
Mode. If not, use C to enter the Hand Setting
Mode.
D
2. Hold down A while in the Hand Setting Mode until
the indicator "
" starts to flash on the dis-
play.
Normal Hand Setting Mode
A few
A few
(the flashing stops)
minutes
minutes
Reminder signal display
AUTO DISPLAY FUNCTION
To turn the Auto Display on
B
Hold down C for about three seconds in any mode
until the watch beeps.
To turn the Auto Display off
D
Hold down C for about three seconds until the watch
beeps. At this time, the watch is in the Timekeeping
Mode.
1353/1361-3
Timekeeping
Mode