Casio 2345 Algemene handleiding - Pagina 4

Blader online of download pdf Algemene handleiding voor {categorie_naam} Casio 2345. Casio 2345 6 pagina's. Watch

Pagina afdrukken

MEMORY

The watch is equipped with memory that you can use to store up to 10

barometric pressure and temperature readings. Note that the date and time of

the measurement is not included with the data. The number of available blank

records that can be used to store data is shown on the right side of the

Barometer and Thermometer Mode screens.

Storing a Measurement

While in the Barometer or Thermometer Mode, hold down D for about one

second until the watch beeps, indicating that the latest measurement is stored

in memory.

• The message "FULL" appears on the display for about one second when

you hold down D while memory is full. No more data can be stored while

memory is full.

• If you want to store more data after memory becomes full, use the

procedure under "Recall Mode" below to delete the current data to make

room for new data.

RECALL MODE

Recalling data

1. Use C to enter the Recall Mode.

2. Each press of D cycles through the barometric pressure and temperature

data in memory. Mode indicators appear to tell you what type of data is

currently displayed.

• Note that measurement units are not indicated on the Recall Mode screens.

• The display shows "- - - - – –" if there is no data.

1 second

later

Recall Mode indicator

Deleting Data

While in the Recall Mode, hold down A. The

watch beeps, and the message CLR flashes

on the display to indicate data is about to be

deleted. Keep A depressed for about two

seconds to delete all the measurement data

currently in memory.

• Note that this procedure deletes all

measurement data in memory. You cannot

delete individual records.

ALARM MODE

When the Daily Alarm is turned on, the alarm sounds for 20 seconds at the

preset time each day. Press any button to stop the alarm after it starts to

sound.

When the Hourly Time Signal is turned on, the watch beeps every hour on the

hour.

Alarm Mode indicator

To set the alarm time

1. Hold down A until the hour digits start to flash on the display. The hour

digits flash because they are selected . At this time the alarm is

automatically turned on.

2. Press C to change the selection in the sequence shown below.

Hour

3. Press D to increase the number or B to decrease it.

• Holding down either button changes the setting at high speed.

4. After you set the alarm time, press A to return to the Alarm Mode screen.

• The format (12-hour and 24-hour) of the alarm time matches the format you

select for normal timekeeping.

• When setting the alarm time using the 12-hour format, take care to set the

time correctly as morning or afternoon.

Memory number

Barometric pressure

Alarm time

1 second

later

Hourly Time Signal on

indicator

Daily Alarm on indicator

Minutes

To stop the alarm

• Press any button to stop the alarm after it starts to sound.

To turn the Daily Alarm and Hourly Time Signal on

and off

Press D while in the Alarm Mode to change the status of the Daily Alarm and

Hourly Time Signal in the sequence shown below.

Both OFF

Both ON

• The Daily Alarm and Hourly Time Signal on indicator is displayed in all

modes.

To test the alarm

Hold down D while in the Alarm Mode to sound the alarm.

• Note that pressing D also changes the Daily Alarm and Hourly Time Signal

on and off settings.

COUNTDOWN ALARM MODE

The countdown alarm can be set within a range of 10 seconds to 60 minutes.

When the countdown reaches zero, an alarm sounds for 10 seconds or until

you press any button.

About Auto-repeat

• When the end of the countdown is reached while Auto-repeat is on, the

alarm sounds, but the countdown restarts from the beginning without

stopping.

• To stop the countdown, press D. You can then manually reset to the start

time by pressing B.

• If you set a starting time of 1 minute or less and have Auto-repeat turned

on, the countdown alarm tone (which normally sounds for 10 seconds)

sounds for only one second.

About the Progress Beeper

• When the Progress Beeper is turned on, the watch beeps as the countdown

time passes the 10, 5, 4, 3, 2, and 1-minute marks, and the 50, 40, 30, 20,

10, 5, 4, 3, 2, and 1-second marks.

• Even if the Progress Beeper is turned on, it does not operate if you set a

starting time of 1 minute or less and have Auto-repeat turned on.

Countdown Alarm Mode indicator

To make countdown alarm settings

1. Hold down A while in the Countdown Alarm Mode. The minites setting

flashes on the display because they are selected .

2. Press C to change the selection in the following sequence.

Minutes

Seconds

3. Press D to increase the selected number or B to decrease it. Holding

down either button changes the setting at high speed.

• The seconds can be set in units of 10 seconds.

• Set 0 minutes, 0 seconds to specify a start time of 60 minutes.

• While the Progress Beeper ON/OFF setting is selected (flashing), press D

or B to toggle the Progress Beeper on and off.

• While the Auto-repeat ON/OFF setting is selected (flashing), press D or B

to toggle Auto-repeat on and off.

2345/2347-4

Hourly Time

Daily Alarm only

Signal only

1 second

later

1/10 second

Seconds

Minutes

Progress beeper

Auto-repeat

BEEP ON/OFF

AUTO ON/OFF