Casio 2362 Handmatig - Pagina 2

Blader online of download pdf Handmatig voor {categorie_naam} Casio 2362. Casio 2362 5 pagina's.

Pagina afdrukken

Note

• If you are using the time calibration signal to set the time for this watch, be sure to

correctly set your home city. Otherwise, there is the chance that the watch will not

set the correct time. See the "To select your Home City code" for details.

• This watch automatically switches between DST and standard time while BER is

selected as the home city code. For any other home city code, you must perform the

procedure under "To set the current digital time and date manually" to switch

between DST and standard time.

• Time calibration reception is limited to specific geographic areas in West Europe.

• The current time setting in accordance with the time calibration signal takes priority

over any time settings you make.

• The watch is designed to automatically update the date and day of the week for the

period January 1, 2000 to December 31, 2039. Setting of the date by the time

calibration signal cannot be performed starting from January 1, 2040.

• This watch can receive signals that differentiate between leap years and non-leap years.

• Auto Receive is turned on when the watch is shipped from the factory.

• See the information under "Time Calibration Signal Reception Precautions" if you

experience problems with time calibration signal reception.

To perform manual time calibration signal reception

1. Place the watch on a stable surface to its top (12

o'clock side) is facing in the general direction of

Frankfurt, Germany.

• Position the watch so the case is pointing upwards as

shown in the nearby illustration. Note that signal

reception is poor if the watch is on its back or side.

• This puts the watch in the optimum position for time

calibration signal reception.

2. In the Timekeeping Mode, hold down D for about two

Receive indicator

seconds, until the watch beeps and the current time is

flashing on the display.

• This indicates that signal reception has started.

• Time calibration signal reception takes from four to 11

minutes. Take care that you do not move the watch

during this time.

• After signal reception is complete, the display of the

Current time

watch changes to the Last Signal screen, which

shows the new signal receive date and time.

Note

• To interrupt a receive operation and return to the Date screen, press D.

• If the receive operation is unsuccessful, the message "ERR" appears on the Last

Signal screen for about one or two minutes. After that, the watch returns to the Date

screen.

• You can also change from the Last Signal screen to the Date screen by pressing D.

About the Receive Indicator

The receive indicator shows the strength of the calibration signal being received. For

best reception, be sure to keep the watch in a location where signal strength is

strongest.

Weak

• Even in an area where signal strength is strong, it takes about 10 seconds for signal

reception to stabilize enough for the receive indicator to indicate signal strength.

• Use the receive indicator as a guide for checking signal strength and for finding the

best location for the watch during signal receive operations.

• The receive indicator remains on the display in all modes following reception of the

time calibration signal and calibration of the watch's time setting. The receive

indicator does not appear if signal reception was unsuccessful or after manual

adjustment of the current time setting.

About Auto Receive

When auto receive is turned on, the watch automatically starts to receive the time

calibration signal when the digital time in the Timekeeping Mode reaches 2:00 AM,

4:00 AM, and 6:00 AM each day (calibration times).

Note

• The Auto Receive operation is performed only if the watch is in the Timekeeping

Mode when one of the calibration times is reached. It is not performed if the

calibration time is reached while you are making settings (while settings are flashing

on the display).

• Auto receipt of the calibration signal is designed to be performed early in the

morning, while you sleep (provided that the digital time is set correctly). Before going

to bed for the night, remove the watch from your wrist, and put it in a location where

it can easily receive the signal.

• The receive indicator (

) indicates that one, two, or all three of the last calibration

time reception attempts were successful.

• When auto receive is turned on, the watch receives the calibration signal for four to

11 minutes each day when the digital time reaches 2:00 AM, 4:00 AM, and 6:00 AM.

Do not operate any of the watch's buttons within 15 minutes prior to or following the

calibration times. Doing so can interfere with correct calibration.

• Remember that reception of the calibration signal depends on the time shown on the

digital display. The receive operation will be performed whenever the digital display

shows 2:00 AM, 4:00 AM, and 6:00 AM, regardless of whether or not the displayed

time is actually the correct time.

• When two or three receptions are successful, the watch uses the data of the last

reception for calibration. When only one reception is successful, the watch uses the

data of the successful reception.

To turn auto receive on and off

1. In the Timekeeping Mode, hold down A until the

current Auto Receive On/Off setting starts to flash,

which indicates the setting screen.

2. Press D to toggle Auto Receive on (ON) and off (OFF).

3. Press A to exit the setting screen.

Strong

Analog Timekeeping

The analog time of this watch is synchronized with the digital time. The analog time

setting is adjusted automatically whenever you change the digital time.

Note

• Whenever you manually change the digital time setting or Home City code, or if the

time is adjusted by receipt of a time calibration signal, the hands of the analog

timepiece move clockwise or counter clockwise to adjust to the new setting. If the

analog time does not match the digital time for any reason, use the procedure

described under "To adjust the analog time" to match the analog setting to the digital

setting.

• Whenever you need manually adjust both the digital and the analog time settings,

make sure you adjust the digital setting first.

• Sometimes when you set the digital time back, the analog time is adjusted by

moving the hands forward to the new time setting. In this case, the message "WAIT"

appears on the digital display while the analog hands are being adjusted.

• Depending on how much the hands have to move in order to adjust to the digital

time, it may take some time before the analog hands stop moving.

• The analog time does not change while a signal receipt operation is in progress.

After the receive operation is complete, the analog time is automatically adjusted to

match the digital time.

To adjust the analog time

1. In the Timekeeping Mode, press C five times to enter

Current time

the Hand Setting Mode.

2. Hold down A until the current digital time starts to

flash, which indicates the setting screen.

• Note that you will not be able to change to the setting

screen if the analog hands are moving because the

watch is automatically adjusting the analog time to

match the digital time. If this happens, wait until the

hands stop moving.

3. Use D (+) and B (–) to adjust the analog setting as described below.

When you want to do this:

Move the hand setting

forward 20 seconds

Move the hand setting back

20 seconds

Move the hand setting a short

way forward at high speed

Move the hand setting a

short way back at high speed

Move the hand setting a long

way forward at high speed

Move the hand setting a long

way back at high speed

4. Press A to exit the setting screen.

• To return to the Timekeeping Mode, press C.

DAY COUNTER

The Day Counter lets you count the number of days from the Timekeeping Mode's

current date to a specific target date.

• There are five Day Counter records, each of which can be set with its own text and

target date (year, month, day).

• All of the operations in this section are performed in the Day Counter Mode, which

you enter by pressing C.

To recall Day Counter records

Enter the Day Counter Mode, and the Target Date/Text screen appears.

Target Date/Text

Target Month – Day

Target year

Text

• Target Date/Text screen alternates between the target month and day, and the target

year.

2362-2

Perform this button operation:

• Press D.

• Press B.

• Hold down D.

• Release D when the hands reach the setting

you want.

• Hold down B.

• Release B when the hands reach the setting

you want.

• While holding down D to move the hands at

high-speed, press B to lock the high-speed

hand movement.

• Press any button when the hands are close to

the setting you want.

• Hand movement stops automatically if the hour

hand makes one full (12-hour) revolution.

• While holding down B to move the hands at

high-speed, press D to lock the high-speed

hand movement.

• Press any button when the hands are close to

the setting you want.

• Hand movement stops automatically if the hour

hand makes one full (12-hour) revolution.

Day Counter

Press A.

Day counter