Dunlop EP103 Handmatig
Blader online of download pdf Handmatig voor {categorie_naam} Dunlop EP103. Dunlop EP103 2 pagina's. Echoplex delay
Pagina afdrukken
EP103 ECHOPLEX
®
DELAY
EP103 ECHOPLEX
DELAY
®
DESCRIPTION
POWER
The Echoplex Delay requires
• Vintage Echoplex EP-3 tape echo
9 volts (240mA) and can be
warmth and modulation
powered by the included Dunlop
• Audiophile quality audio paths
ECB003/ECB003EU adapter or
• 100% analog dry path
the Iso-Brick
Power Supply.
™
• Studio-grade low noise floor
This pedal cannot be powered
• Age control varies delay tone
by a battery.
from pristine to dark and dirty
COMBINING WITH THE EP101
• Delay control provides 65–750ms
ECHOPLEX PREAMP
of delay time
To combine the EP103 with the
• Tap jack provides up to 4
EP101 Echoplex Preamp for the full
seconds of delay time with
Echoplex EP-3 experience, simply
external Tap Tempo Switch
run the EP101 in front of the EP103.
CONTROLS
VOLUME knob sets effect signal
level (dry signal is always set
to unity) and adjusts Age mode
SUSTAIN
DELAY
(indicated by AGE LED)
VOLUME
SUSTAIN knob sets number
AGE
of repeats
DELAY knob sets delay time
FOOTSWITCH toggles
4
effect on/bypass (red LED
indicates on)
TAP input allows for the
5
DELAY
MXR Tap Tempo Switch (not
included) to set delay tempo
STEREO/MONO switch
6
(internal) toggles stereo/mono
6
input functionality
STEREO
MONO
DIRECTIONS
• Run a standard cable from your
3. Push VOLUME control to lock
guitar to the EP103's INPUT
your Age setting and return to
jack and another cable from
normal operation.
the EP103's OUTPUT jack
4. AGE LED indicates Age mode is
to your amplifier.
active. Press once on VOLUME
• Start with all controls at 12 o'clock.
control to toggle between your
Age setting and the default
• Turn effect on by depressing
clear, pristine sound (LED off).
the footswitch.
• Rotate SUSTAIN control clockwise
TAP TEMPO
to increase number of repeats or
To use the EP103's Tap Tempo
counterclockwise to decrease it.
function, connect a cable from
• Rotate VOLUME control clockwise
the EP103's TAP jack to the M199
to increase effect volume or
MXR Tap Tempo Switch's INPUT
counterclockwise to decrease it.
jack. Tap the M199's switch two
or more times to set time between
• Rotate DELAY control clockwise to
repeats, up to a full 4 seconds.
increase delay time up to 750ms
or counterclockwise to decrease
STEREO MODE
it to a minimum of 65ms.
The EP103 can be run in either
Mono (default) or Stereo modes,
AGE MODE
selectable via internal switch,
The EP103's Age function simulates
which determines tip/ring input
the sonic qualities of an aging
connection. For a stereo setup,
EP-3. To access:
run a TRS splitter cable to the
1. Push and hold VOLUME
EP103's INPUT jack and another
control for 2 seconds until
from the EP103's OUTPUT jack to
AGE LED flashes.
your amplifier. Next, set internal
2. Rotate VOLUME control
STEREO/MONO switch to its LEFT
counterclockwise for a bright,
position. Note: When EP103 is
pristine tape echo sound; rotate
bypassed, output ring connection
control clockwise for a darker
will only receive signal if EP103
and more modulated, aged tape
is set to Trails Bypass mode (see
echo sound.
TRAILS BYPASS MODE section).
ADVANCED FUNCTIONS –
TRAILS BYPASS MODE
STARTUP MODE
The EP103 normally operates
Additional functions can be
using a "true bypass" relay, which
accessed by entering Startup Mode.
shuts off the effect and hardwire
Advanced function settings remain
bypasses the tip connection signal
in selected state, even after pedal is
as soon as you turn the pedal off
powered off. Re-enter Startup Mode
(ring connection uses a buffered
and repeat relevant steps to change
bypass). The EP103 can also be
the settings again.
operated using Trails Bypass
1. Disconnect EP103 from power
mode, which uses a buffered
supply and set SUSTAIN and
bypass and allows the reverb
DELAY controls to 12 o'clock.
effect to ring out even after
2. Enter Startup Mode by pushing
turning the pedal off.
down and holding VOLUME knob
1. After entering Startup Mode,
while connecting EP103 to its
release VOLUME knob. AGE
power source.
LED will reflect bypass mode
status. Green indicates default
WET MODE
True Relay Bypass mode; red
To set the EP103 to send only the
indicates Trails Bypass mode.
wet signal to your amplifier:
2. Press VOLUME knob to toggle
1. After entering Startup Mode,
between modes.
observe AGE LED for mode
status while still holding down
3. Depress footswitch to exit
VOLUME knob. Green indicates
Startup Mode and resume
default Dry mode. Red indicates
normal operation.
Wet mode.
NOTE:
2. While still holding down VOLUME
You may notice that the EP103's
knob, rotate SUSTAIN or DELAY
housing warms up while on.
knob clockwise past 12 o'clock to
This is completely normal. Take
select Wet mode (red LED). To re-
care when operating in extremely
turn to Dry mode, rotate SUSTAIN
high ambient temperatures or
or DELAY knob counterclockwise
direct sunlight.
past 12 o'clock (green LED).
3. Release VOLUME knob to save
selection. Depress footswitch to
resume normal operation.