Free The Tone TA-1H Gebruikershandleiding - Pagina 4

Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Free The Tone TA-1H. Free The Tone TA-1H 6 pagina's. Multi-dimensional chorus
Ook voor Free The Tone TA-1H: Procedures voor firmware-updates (11 pagina's)

Pagina afdrukken

THREE OPERATING MODES

The TRI AVATAR has three operating modes: Manual, Preset, and Edit. Manual

and Preset modes are toggled by pressing the MODE switch. Edit mode is

activated by the EDIT switch. In Edit mode you can modify preset contents and

save them in a preset memory.

3-1. Manual Mode

The MANUAL LED above the MODE switch illuminates when the unit is operating

in Manual mode. In Manual mode, chorus sound is set by the position of each

knob. When an expression pedal is connected to the EXP terminal, the setting

defined by the RATE or HI-CUT knob's position is disabled and the parameter is

controlled from the expression pedal.

3-2. Preset Mode

The PRESET LED above the MODE switch illuminates when the unit is operating

in Preset mode. In this mode the chorus sound stored in the preset selected by

the Select footswitch is recalled. (Each of the four presets contains a sample

setting when shipped from our factory.)

When an expression pedal is connected to the EXP terminal, the RATE or HI-CUT

settings stored in the presets are disabled and you can modify these parameters

from the expression pedal. In Preset mode turning each knob does not modify the

chorus sound. This can avoid an unnecessary change of chorus sound due to an

unintentional change to the knob angle. Preset contents can be modified in Edit

mode explained below.

3-3. Edit Mode

The EDIT LED above the EDIT switch illuminates when the unit is operating in Edit

mode. This mode, activated by pressing the EDIT switch, is for modifying and

writing preset contents.

• If the unit enters Edit mode from Preset mode

You can change only the desired parameters from the current preset sound and

save them to the original or another preset.

1. Press the EDIT switch to enter Edit mode.

2. Adjust the desired parameter's knob.

3. Press the Select footswitch to select the target preset number. If you want to

overwrite the current preset, do not press the Select footswitch.

The target preset number's LED is flashing for your confirmation.

4. Press and hold the EDIT switch for about 1.5 seconds. The EDIT LED starts

flashing and the preset is saved in the memory. When saving completes,

the unit automatically switches from Edit to Preset mode and recalls the stored

preset.

If the EDIT switch is pressed again after turning the knobs to modify the

parameters in Edit mode, then your changes are canceled and the unit

returns to the status in which the original preset is recalled.

• If the unit enters Edit mode from Manual mode

The current Manual mode settings are saved in the preset memory.

1. Press the EDIT switch to enter Edit mode.

2. Press the Select footswitch to select the target preset number. The selected

preset number's LED is flashing for your confirmation.

3. Press and hold the EDIT switch for about 1.5 seconds. The EDIT LED starts

flashing. When saving completes, the unit automatically switches from Edit to

Preset mode and recalls the stored preset.

Pressing the EDIT switch again when in Edit mode returns the unit to Manual

mode without executing a save operation.

FACTORY PRESETS

The TRI AVATAR has four chorus sounds as factory presets. These settings will be

lost by overwriting user presets but can be restored by initializing the TRI AVATAR.

S p a c i o u s t h re e - p h a s e

P R E S T - 1

chorus sound without uncomfortable

pitch feeling. Dry sound is zero and

WET is 100%.

W ide and round chorus

PREST-3

sound with lesser chorus effect.

Warm and fat chorus sound

PREST-2

created by mixing dry (original) sound

with three-phase chorus sound.

Sound with vibrato effect.

PREST-4

Vibration speed can be controlled in

real-time from an expression pedal

connected to the EXP terminal.