Audiodesign TRIO LA 6/10 Gebruikershandleiding - Pagina 3
Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Audiodesign TRIO LA 6/10. Audiodesign TRIO LA 6/10 4 pagina's. Full range sound system
Portable Full Range Sound System TRIO LA 6/10
Volume setting of the system is made by means of the three LEVEL
knobs on top of the subwoofer:
- Left satellite is GAIN LEFT
6
6
- Right satellite is GAIN RIGHT
- Subwoofer is GAIN SUBWOOFER
3
Before switching power on and proceed to system setting, make sure that
all three knobs are completely turned counterclockwise, at level 0, and that the mixer output is set so that the peaks level
stays about within 0 e +3 dB.
Set first the satellites volume alone and then the subwoofer volume alone.
Satellites Volume setting
Switch power on and begin to turn clockwise the satellite GAIN knobs
to flash shortly for less than 1 second.
This is the optimal level being connected to a mixer sending to MAIN a signal with level peaks within 0 and +3dB.
Now listen to the satellites with this output level; if you detect distorsion or saturation of the signal (i.e of microphone) check
the possibility of reducing the level of the signal concerned at his source, otherwise try to slightly lower the mixer's main
otput. Should this not be enough, reduce the satellites volume until you have an optimal sound.
Memorize the knobs setting.
Sub Volume setting
After having memorized the knobs setting LEFT e RIGHT, take them back to 0 and begin now to turn clockwise the
SUBWOOFER GAIN knob
3
until the correspondent PEAK led begins to flash shortly for less than 1 second.
This is the optimal level being connected to a mixer sending to MAIN a signal with level peaks within 0 and +3dB.
Now listen to the Sub with this output level; if you detect distorsion of basses, turn slightly the knob back counterclokwise.
Final system setting
Bring the three knobs at the optimal level you have checked and listen to the complete system, again at the mixer
main level peaks between 0 and +3 dB.
If you detect to much basses compared with satellites output, turn slightly back the SUB LEVEL knob.
If you detect instead not enough basses, turn slightly back the setellites LEVEL LEFT and RIGHT knobs.
As a general rule , the output level of the mixers should be set so that the sound peaks remain between 0 to +3 dB
about. When the system TRIO MASTER gets in the two Line In (10 and 11) a signal with that amplitude and it is
set as explained above, it grants the maximum performance in terms of maximum undistorted amplification (at clip
limit) and in this conditions you get the maximum possible sound pressure (SPL).
RESPONSE DIAGRAM OF SYSTEM TRIO LA 6/10
Sensitivity Magnitude
95.0
90.0
85.0
80.0
75.0
70.0
65.0
60.0
55.0
50.0
45.0
BVUP
20.0
100.0
AUDIODESIGN PRO: TRIO LA 6/10
6
3
PEAK
PEAK
PEAK
L
HI PASS
HIGH
GAIN
LOW PASS
GAIN
80
80
PHASE
SHIFT
60
120
60
120
0 - 180°
50
260
-15
+15
0
10
50
260
0
Hz
Hz
LEFT speaker
Subwoofer
6
until the correspondent PEAK led begins
@ 1W/1m
-
dB SPL/watt (4 ohm load)
1000.0
10000.0
log Frequency - Hz
MLSSA: Frequency Domain
- 6 -
6
SYSTEM COMPONENTS
The TRIO LA 6/10 stereo system is composed by three elements:
PEAK
GAIN
HIGH
HI PASS
R
80
60
120
10
0
10
-15
+15
50
260
Hz
POWER
Active Subwoofer STAGE PRO W10
R IGHT speaker
Connections and Control Panels
8
7 6 5
2
PEAK
PEAK
L
HI PASS
HIGH
GAIN
LOW PASS
80
80
60
120
60
50
Hz
260
-15
+15
0
10
50
Hz
260
LEFT speaker
Subwoofer
Portable Full Range Sound System TRIO LA 6/10
The active subwoofer STAGE PRO W10 is equipped with a
10" (250 mm) woofer with 50 mm VC.
The cabinet integrates all necessary electronics for amplification and system
processing:
3 amplifiersi in AB Class for a total power of 500 W RMS (1000 W Max)
1 x 250 W RMS (500 W Max) for the Subwoofer itself
2 x 125 W RMS (250 W Max) for the two passive satellites (@ 4 Ohm load)
The Subwoofer signal is LowPass filtered, adjustable from 46 to 240 Hz 12 dB/oct.
The Satellites signals are HighPass filtered, adjustable from 38 to 250 Hz 12 dB/oct.
Cabinet of high density MDF, anti-scratch embossed painting
Practical transport handles hollowed into the wood
Integral rigid metal grill
Housing hole for ø 35 mm stand tubes
Sizes & weight: 43 x 39 x 39 cm; 32 kg.
1
Subwoofer Clip Indicator
2
Subwoofer LOW PASS control adjustable from 46 to 240 Hz
1
3
5 6 7 8
Subwoofer Volume control
3
4
Phase Switch 0-180°
PEAK
PEAK
R
GAIN
GAIN
HIGH
HI PASS
80
PHASE
SHIFT
120
0 - 180°
60
120
Satellites Clip Indicator (Separated Left and Right)
0
10
0
10
-15
+15
50
Hz
260
5
POWER
R IGHT speaker
6
Satellites Volume control separated on channel LEFT and RIGHT.
4
9
it controls only the signal going respectively to left and right satellite.
High tones equalization separated for left and right channel -15 / +15 dB
7
8
Satellites HI PASS control separated LEFT and RIGHT from 38 to 250 Hz
13
12
11
10
18
ATTENTION: the HI PASS frequency should not be set under 120 Hz
9
ON LED indicator (Red)
OUTPUT
LINE IN
OUT+:1+/ OUT- :1-
10
Right Channel Line In
Combo Socket XLR 3-F / Jack 6,3 mm Balanced
ST
MONO
LEFT
RIGHT
LEFT(Mono)
RIGHT
SPEAKER OUTPUT:
GND=1=SLEEVE HOT=2=TIP COLD=3=RING
Left Channel Lin In
11
Combo Socket XLR 3-F / Jack 6,3 mm Balanced
Speakon Socket Right Satellite
12
13
Speakon Socket Left Satellite
Amplifier cooling fan; keep it clean for a correct ventilation.
14
15
On/Off power switch - In positioe 0 the system is Off
Voltage Selector
16
Power Net Socket
17
ST/MONO Switch (Stereo / Mono): se si seleziona STEREO,
18
When STEREO is selected, the system sends to the Right and Left channels the
correspondent Right and Left input signals.
When
MONO is selected,
the LEFT input signal, so one complete system per channel can be used..
- 3 -
1 Active Subwoofer STAGE PRO W10
2 Passive Satellites STAGE LA 6
the system sends to both Right and Left channels only