Casit KEQ016 Handmatig - Pagina 5

Blader online of download pdf Handmatig voor {categorie_naam} Casit KEQ016. Casit KEQ016 6 pagina's. Electronic panel

Pagina afdrukken

EXTENDED MENU 2

The control unit is supplied by the manufacturer with the

possibility of directly selecting the main menu functions only.

To enable the functions listed in Extended Menu 2, proceed as

follows: open Extended Menu 1 (as instructed in the respective

section), then press and hold the SET key for 5 seconds, the T.

PAUSA LED and RIT. ANTE LED will flash simultaneously,

accordingly, you have 30 seconds to select the functions of

Extended Menu 2 using the SEL and SET buttons. After

another 30 seconds, the control unit returns to the main menu.

----------------------

EXTENDED MENU 2

Reference LED

LED Off

A) AUT / P-P

Follow Me = OFF

B) CODE

PreFlash. and Cort. L=OFF PreFlash. or Cort. L. =ON

C) CODE PED.

Pause Lamp. = OFF

D) INB.CMD.AP SOFT START = OFF

E) T. MOT.

El. Gate CMD PED = OFF

F) T.MOT.PED.

PUL=PUL - PED=PED

G) T. PAUSA

Flashing beacon ON/OFF simultaneous

H) RIT. ANTE

Flashing beacon ON/OFF in simultaneous

A) AUT/P-P ( Follow Me ) :

It is possible to set the "Follow Me" function on the control unit:

this function can only be programmed if a Pause Time has

already been programmed, and it is used to shorten the Pause

time to 5 sec after the photocell DS1 disengages, i.e. the gate

closes 5 seconds after the user has passed through.

wish to enable the function, proceed as follows: make sure that

you have enabled Extended Menu 2 (T. PAUSA LED and RIT.

ANTE LED start flashing simultaneously), with the SEL key

position on the flashing of

key, the AUT/P-P LED will simultaneously switch on steadily

and programming is completed. Repeat the procedure to

restore the previous configuration.

B) CODE ( Pre-flashing / Courtesy Light ) :

The control unit is supplied by the manufacturer with Pre-

flashing and Courtesy Light functions disabled. If you wish to

enable the Pre-flashing function, proceed as follows: make sure

that you have enabled Extended Menu 2 (T. PAUSA LED and

RIT. ANTE LED start flashing simultaneously), with the SEL key

position on the flashing of CODE LED then press the SET key,

the CODE LED will simultaneously switch on permanently and

the programming is completed. If you wish to enable the

Courtesy Light, repeat the operation described above, pressing

the SEL button twice instead of once (the CODE LED will flash

rapidly).

Repeat the operation to restore the initial configuration.

Pre-flashing** function The flashing beacon 230 Vac is

always activated 3 seconds before the automation starts any

type of motion.

Courtesy Light Function:

output will be activated for 3 minutes, each time that an

opening command is given.

C) CODE PED ( Flashing beacon function ) :

The control unit is supplied by the manufacturer with the

flashing beacon function during the enabled Pause Time. If you

wish to disable the function, proceed as follows: make sure that

you have enabled Extended Menu 2 (T. PAUSA LED and RIT.

ANTE LED start flashing simultaneously), with the SEL key

position on the flashing of PED CODE LED then press the SET

key, the PED CODE LED will simultaneously switch on

permanently and programming is completed. Repeat the

procedure to restore the previous configuration.

D) INB. CMD. AP. LED ( SOFT START ) :

The control unit is supplied by the manufacturer with the Soft

Start function disabled. If you wish to enable the function,

Pagina 5 di 6

-----------------

LED On

Follow Me = ON

Pause Lamp. = ON

SOFT START = ON

El. Gate CMD PED = ON

PUL=AP - PED=CH

AUT/ P-P LED then press the SET

The Flashing beacon 230 Vac

proceed as follows: make sure that you have enabled Extended

Menu 2 (T. PAUSA LED and RIT. ANTE LED start flashing

simultaneously), with the SEL key position on the flashing of

INB.CMD.AP LED then press the SET key, the INB.CMD.AP

LED will simultaneously stay on steadily and programming is

completed. Accordingly, every time the gate starts motion the

control unit will control motor start-up, increasing the power

gradually from minimum to maximum in the first two seconds of

operation. Repeat the procedure to restore the previous

configuration.

E) T. MOT. (Electric Lock activation CMD PED.) :

The control unit is supplied by the manufacturer with the

activation of the electric lock through the disabled Pedestrian

command. If you wish to enable the function, proceed as

follows: make sure that you have enabled Extended Menu 2 (T.

PAUSA

LED

simultaneously), with the SEL key position on the flashing of

T.MOT. LED then press the SET key, the T.MOT. LED will

simultaneously switch stay on steady and programming is

completed. The activation of the electric lock function through

the Pedestrian command, is used when you have, for example,

a sliding gate with a door next to the Pedestrian passage.

Accordingly, the gate can be opened with the PUL commands

as well as from the Pedestrian door using the electric lock with

the PED. commands.

restore the previous configuration.

If you

F) T. MOT. PED ( PUL and PED command functions ) :

The control unit is factory supplied with PUL control input

operation for the connection of a cyclical primary control button

(NA) and a PED input for the connection of a cyclical

Pedestrian command button (NA). If you wish to select another

mode of function of the PUL and PED inputs, proceed as

follows: make sure that you have enabled Extended Menu 2 (T.

PAUSA

LED

simultaneously), by using the SEL key select the flashing T.

MOT PED. LED and press the SET button: T. MOT. PED.

LED remains steadily lit and programming is complete.

Accordingly, the PUL input makes it possible to connect a

button (NA) for the Opening phase only, and the PED input for

connection to a button (NA) for the Closing phase only. Repeat

the procedure if you wish to restore the previous configuration.

EXTENDED MENU 3

The control unit is supplied by the manufacturer with the

possibility of directly selecting the main menu functions only.

To enable power programming

carried out by the control unit,

Extended Menu 2 (as instructed in the respective section), then

press and hold the SET key for 5 seconds, after which the T.

PAUSA LED and RIT. ANTE LED will start flashing alternately

and then simultaneous, in this way there will be 30 seconds to

select the desired deceleration using the SEL and SET keys,

then, after a further 30 seconds, the control unit returns to the

main menu.

----------------------

Level

AUT / P-P - CODE - CODE PED. - INB. CMD. AP. LED

AUT / P-P - CODE - CODE PED. – INB. CMD. AP - T. MOT.

AUT / P-P - CODE -CODE PED. - INB. CMD. AP - T. MOT. - T.MOT.PED.

and

RIT.

ANTE

LED

Repeat the procedure if you wish to

and

RIT.

ANTE

LED

functions for deceleration

proceed as follows: open

EXTENDED MENU 3

Leds On

AUT / P-P

AUT / P-P - CODE

AUT / P-P – CODE – CODE PED.

Rev. 1.1 del 12-03-2015

start

flashing

start

flashing

-----------------