Contemporary Research ICC1-232 Producthandleiding - Pagina 11
Blader online of download pdf Producthandleiding voor {categorie_naam} Contemporary Research ICC1-232. Contemporary Research ICC1-232 13 pagina's. Rs-232 display controller, 1-way control
Ook voor Contemporary Research ICC1-232: Specificaties (2 pagina's), Producthandleiding (16 pagina's)
Pagina afdrukken
ICC-Net Commands
Command
Channel Up
TU
Channel Dwn
TD
T Channel Prev
TP
Force Channel
TC
Select Channel
TT
Tune HD
TH
Ex:
Select Channel
TT
Tune Ring
TR
Control Lock
LM
Sharp Tuning
H9
Send IR
LQ=
Contemporary Research
Description
NA
NA
NA
"$A5,<dh>,<dl>,3,'TC', <channel>" (7 bytes) – Tunes to a specific channel 2-127
"$A5,<dh>,<dl>,2,'TT',<channel>" (7 bytes) – Same as TC
"$A5,<dh>,<dl>,5,'TH',<H1>,<Major>,<Minor>" (9 bytes) – Digital Tuning
Normally, the H1 parameter is 0, allowing the ICC1-232 to use the current H1 tuning
format, but it could be used to force a different tuning option. When the display is set to
the H1=1 mode, 1-part digital channel, the first byte is (x*256), and the last byte is the
value you add to state the channel number. In H1=2 or 3 modes, the bytes represent the
Major and Minor channel numbers.
"$A5,1,4,5,'TH',1,2,3" Device 260, channel 515 (512 +3)
"$A5,1,4,5,'TH',2,2,3" Device 260, virtual channel 2-3
"$A5,1,4,5,'TH',3,2,3" Device 260, physical channel 2, minor 3
See Page 5 for instructions on using the TH command to select inputs.
"$A5,<dh>,<dl>,2,'TT',<channel>" (7 bytes) – Same as TC
"$A5,<dh>,<dl>,<ncb>,'TR', [<chan 1>, <chan N>]" (variable bytes)
This command stores a Tune Ring, Analog channels only, a series of preset channels
accessed by channel up/down commands. This is only for old Smart TVs.
Ex1: "$A5,<dh>,<dl>,6,'TR', 5,4,8,11" sets ring to channels 5, 4, 8 and 11
Tip: The ring follows the stored order, channels do not have to be in ascending
order
Ex2: "$A5,<dh>,<dl>,8,'TR', $82,5,$87,11" sets channels 2-5 and 7-11. You can
specify a range using MSB bit for the first channel; the next byte is the last.
"$A5,<dh>,<dl>,3,'LM',<control>" (7 bytes)
0 = Off (unlocked)
1 = On (locked)
Locks out display commands from an IR remote or front-panel buttons. Feature is not
available for all models of displays. Check with CR Tech Support if this function is
important to your application.
"$A5,<dh>,<dl>,3,'H9',<control>" (7 bytes)
Used for Sharp control firmware 3.2.
H9,1 = Sharp -1 tuning fix (set can't tune a -1 channel, does fine on others)
H9,0 = Standard Sharp control
"$A5,<dh>,<dl>,3,'LQ',<IR Code>" (7 bytes)
Emulates an IR command for special applications:
100=Info
115=Captions
22=Channel Up
23=Channel Down
11
ICC1-232 Manual