Apollo 51000-355 Installatiehandleiding - Pagina 3

Blader online of download pdf Installatiehandleiding voor {categorie_naam} Apollo 51000-355. Apollo 51000-355 16 pagina's. Wireless smoke heat alarm

Pagina afdrukken

BATTERY INSTALLATION AND REPLACEMENT

To replace the batteries:

1. Remove the detector from its mounting base by twisting the detector

counterclockwise. Remove and dispose of the batteries according to

your local regulations.

2. To ensure proper power-down sequence, wait a minimum of 20

Off

seconds before installing new batteries.

3. Install 3 new AAA batteries (available from your local Duracell or

Energizer dealer) in the battery compartment. Follow the polarity

diagram inside the compartment. If the batteries are incorrectly

inserted please remove gently with a non-conductive tool and

correctly reinsert

4. Reinstall the detector onto the mounting base by turning the detector

clockwise until the mating marks align.

5. After the power-up sequence the green LED should blink about once

every 12 seconds to indicate normal operation. If the batteries are not

installed correctly, the detector will not operate and the batteries may

be damaged. If the detector does not power-up, check for correct

batteries installation and for a fully charged batteries.

Off

6. Test the detector (as described later).

CONSTANT EXPOSURES TO HIGH OR LOW TEMPERATURES OR HIGH

HUMIDITY MAY REDUCE BATTERY LIFE.

Off

HUSH/TEST BUTTON

Fig 1. Wireless Smoke Heat Alarm

the transmitter sends a low battery message to the control panel, which

displays the detector's ID at low battery. In addition, the yellow LED of the

detector will blink every 12 seconds. The detector's sounder will chirp every

48 seconds (yellow LED continues to blink) until the batteries are replaced.

Pressing the hush button will silence the chirps for 12 hours, if no other

trouble conditions exist. The batteries should be replaced WHEN the chirps

begin. Be sure to replace the batteries with fresh ones.

BATTERY INSTALLATION AND REPLACEMENT

To replace the batteries:

1. Remove the detector from its mounting base by twisting the detector

counterclockwise. Remove and dispose of the batteries according to your

local regulations.

2. To ensure proper power-down sequence, wait a minimum of 20 seconds

before installing new batteries.

3. Install 3 new AAA batteries (available from your local Duracell or Ener-

gizer dealer) in the battery compartment. Follow the polarity diagram inside

HUSH/TEST BUTTON

BATTERY COMPARTMENT

Fig 1. Wireless Smoke Heat Alarm

relative to the stairway so as to intercept smoke coming from a ﬁ re in the

basement before the smoke enters the stairway.

Smoke detectors are optional where a door is not provided between living

PROGRAMMING

room and recreation room (Figure 5).

The smoke from a ﬁ re generally rises to the ceiling, spreads out across

Refer to the appropiate compatible control panel programming guide for

the ceiling surface, and begins to bank down from the ceiling. The corner

the proper procedure required to enroll the wireless smoke/heat into the

where the ceiling and wall meet is an air space into which the smoke could

system.

have difﬁ culty penetrating. In most ﬁ res, this dead air space measures

about 0.1m (4in.) along the ceiling from the corner and about 0.1m (4in.)

RECOMMENDED LOCATIONS FOR SMOKE HEAT ALARM

down the wall. Detectors should not be placed in this dead air space, see

Figure 6,7 and 8.

According to National Fire Protection Association (NFPA) the major threat

from fire in a dwelling unit occurs at night when everyone is asleep.

Where NOT to install the alarm:

The principal threat to persons in sleeping areas comes from fires in

the remainder of the unit; therefore, a smoke detector(s) is best located

- Directly above a sink, cooker, stove or oven

between the bedroom areas and the rest of the unit. In units with only one

- Do not locate detector within 5 feet (1.5 m) of any cooking appliance

bedroom area on one floor, the smoke detector(s) should be located as

- Next to a door or window that would be affected by drafts i.e. extractor fan

or air vent

shown in Figure 2. In dwelling units with more than one bedroom area or

- Outside

with bedrooms on more than one floor, more than one smoke detector is

- Do not install in any environment that does not comply with the detector's

required, as shown in Figure 3.

environmental speciﬁ cations

Dining

room

Living room

Fig 2. Location of the detectors

in units with only one bedroom

area on one ﬂ oor

In addition to smoke detectors outside of the sleeping areas, the device

should be installed on each additional story of the dwelling unit, including

the basement. These installations are shown in Figure 4. The living area

smoke detector should be installed in the living room or near the stairway

to the upper level, or in both locations. The basement smoke detector

should be installed in close proximity to the stairway leading to the floor

above. Where installed on an open-joisted ceiling, the detector should

be placed on the bottom of the joists. The detector should be positioned

relative to the stairway so as to intercept smoke coming from a fire in the

basement before the smoke enters the stairway.

INST APD0601 A140513

Kitchen

BedroomBedroom

room

Bedroom

Fig 3. Location of the detectors in

dwelling units with more than one

bedroom area or with bedrooms on

more than one ﬂ oor

Fig 7. Example

Dining

Kitchen

Bedroom

room

Living room

Bedroom

INST APD0601 C160927