Datalogic S5N-PR Gebruiksaanwijzing

Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Datalogic S5N-PR. Datalogic S5N-PR 7 pagina's.
Ook voor Datalogic S5N-PR: Gebruiksaanwijzing (9 pagina's)

Pagina afdrukken

This product is covered by one or more of the following patents.

European Patent 851,211 B1; 1,111,690 B1; 1,148,346 B1; 1,209,487 B1.

Italian Patent IT 1,321,772.

S5N-Px-...-PP/NN SERIES

INSTRUCTION MANUAL

CONTROLS

OUTPUT LED (S5N-Px...A00/B01/C01/C10/C21/D00/E01/F01/T01)

The yellow LED ON indicates that the NO output status is closed.

STABILITY LED (S5N-Px...B01/C01/C21/E01/F01)

The green LED ON indicates that the received signal has a reserve

greater than 30% compared to the output switching value.

POWER ON LED (S5N-Px...G00)

The green LED indicates that the sensor is operating.

TRIMMER (S5N-Px...B01/C01/C21/E01/F01/T01)

The trimmer can be used to adjust sensitivity; the operating distance

increases turning the trimmer clockwise.

WARNING: The trimmer rotation is limited to 270° by a mechanical stop.

Do not apply excessive torque when adjusting (max 40 Nmm).

INSTALLATION

The sensor can be fixed by means of the M18x1 threaded body through

a  18mm hole, using the specific washer and the two CH.24 nuts

enclosed (1.5Nm maximum tightening torque).

Alternatively, the sensor can be mounted through the two housing's

holes using two screws (M3x22 or longer) and washer.

Amongst the various possible solutions, we suggest to choose the

combination that offers the best visibility of the signalling LEDs and the

easiest access to the trimmer.

Wide range of accessories available: 22mm nuts, h=8mm, (2Nm

maximum tightening torque) guarantee an improved torque and various

orientable fixing brackets ease the sensor

positioning (please refer to the accessories

listed in the general catalogue).

The operating distance is measured from the

front surface of the sensor lens.

C models: To improve the detection, the

object has to be moved closer or further away

from the front surface of the sensor lens.

In case of lateral translation, the object must

move as indicated in the figure.

CONNECTIONS

The connections are compliant to the EN 60947-5-2 standard.

S5N-Px...G00

BROWN

10 ... 30 Vdc

WHITE

NC OUTPUT

BLACK

NO OUTPUT

BLUE

0 V

M12 CONNECTOR

AXIAL VERSION

14.5

1.5

3.5

2.5

TRIMMER

N°.2 Ø3.8

STABILITY LED

OUTPUT LED

FIBRE OPTIC VERSION

39.5

Power supply:

Ripple:

Current consumption

(output current excluded):

Outputs:

Output current:

Output saturation voltage:

Response time:

Switching frequency:

Indicators:

Setting:

Operating temperature:

Storage temperature:

10 ... 30 Vdc

Insulating strength:

Insulating resistance:

TEST +

Operating distance (typical values):

TEST -

0 V

Emission type:

Ambient light rejection:

Vibrations:

Shock resistance:

Housing material:

Lens material:

Mechanical protection:

Connections:

Weight:

AtEx 2014/34/EU:

DIMENSIONS

RADIAL VERSION

1.5

3.5

14.5

M O D E L S

with trimmer

without trimmer

N°.2 Ø3.8

72.5

14.5

1.5

6.2

TRIMMER

N°.2 Ø3.8

STABILITY LED

OUTPUT LED

TECHNICAL DATA

S5N-PA AXIAL VERSION

10 ... 30 Vdc (limit values)

2 Vpp max.

35 mA max.

NO and NC; PNP or NPN (short-circuit protection)

100 mA max.

2 V max.

0.5 ms (2 ms mod.F01/G00)

1KHz (250 Hz mod.F01/G00)

OUTPUT LED (YELLOW) excluding mod.G00

STABILITY LED (GREEN) (mod.B01/C01/C21/E01/F01)

POWER ON LED (GREEN) (mod.G00)

sensitivity trimmer (mod.B01/C01/C21/E01/F01/T01)

-25 ... 55 °C

-25 ... 70 °C

500 Vac 1 min., between electronics and housing

>20 M 500 Vdc, between electronics and housing

A00: 0.1...4 m on R2

B01: 0.1...3.5 m on R2

C01: 0...60 cm

C10: 0...10 cm

C21: 0...35 cm

D00: 0.5...10 cm

F01/G00: 0...25 m

E01: 30 mm with OF-42 / 100 mm with OF-43

T01: 0.1...1 m on R2

red (630 nm) (mod. D00/E01) / red (660 nm) (mod.B01/T01) /

infrared (880nm) (mod. A00/C01/C10/C21/G00)

according to EN 60947-5-2

0.5 mm amplitude, 10 ... 55 Hz frequency, for every axis (EN60068-2-6)

11 ms (30 G) 6 shock for every axis (EN60068-2-27)

PBT

PMMA

IP67

2 m cable  4 mm / M12 - 4 pole connector

75 g. max. cable vers. / 25 g. max. connector vers.

II 3D EX tc IIIC IP67 T85°C

Setting of S5N-Px...A00

14.5

Position the sensor and reflector on opposite sides.

Find the points where the yellow LED (OUT) is wswitched ON and OFF in

both vertical and horizontal posizionts, and fix the sensor in the center

between these points.

Setting of S5N-Px...B01/T01

Position the sensor and reflector on opposite sides.

Turn the sensitivity trimmer to the maximum position.

Moving the sensor both vertically and horizontally, determine the power on and off

points of the yellow LED (OUT) and then mount the sensor in the middle of the

points defined. Optimum operation is obtained when the green LED (mod.B01) is

TRIMMER

ON and the yellow LED is OFF.

M O D E L S

B01 models: If necessary reduce sensitivity in order to detect very

with trimmer

without trimmer

small targets. In order to improve alignment, repeat the procedure

detailed above whilst progressively reducing the sensitivity.

STABILITY LED

T01 model: Turn the sensitivity trimmer counterclockwise until the

OUTPUT LED

yellow LED turns ON (pos.A). Turn slowly the trimmer again clockwise until the

yellow LED turns OFF (Operating condition, pos.B).

Setting of S5N-Px...F01/G00/E01 with OF-43 (P/R fibre-optics)

Position the sensors (fibre terminals) on opposite sides.

CABLE VERSION

Turn the sensitivity trimmer to maximum: moving the sensor both vertically and

horizontally, determine the power on and off points of the yellow LED (OUT) and

then mount the sensor in the middle of the points defined. Optimum operation is

obtained when the green LED is ON and the yellow LED is OFF (the output

function and the relative LEDs are inverted in the E01 model with the OF-43 fibre).

If necessary, reduce sensitivity using the trimmer, in order to detect very small

targets. In order to improve alignment, repeat the procedure detailed above whilst

progressively reducing the sensitivity.

Setting of S5N-Px...C01/C21/E01 with OF-42 (proximity fibre)

Turn the sensitivity trimmer to minimum: the green LED is ON, the yellow LED is

STABILITY LED

OFF. Position the target to detect in front of the sensor or of the fibre terminals.

OUTPUT LED

Turn the sensitivity trimmer clockwise until the yellow LED turns ON (Target

detected state, pos.A).

Remove the target, the yellow LED turns OFF.

Turn the sensitivity trimmer clockwise until the yellow LED turns ON (Background

detected state, pos.B).

The trimmer reaches maximum if the background is not detected.

Turn the trimmer to the intermediate position C, between the two positions A and

B. The green LED must be ON.

Setting of S5N-Px...C10/D00

S5N-PR RADIAL VERSION

The operating distance range of these sensors is factory preset: please consider

this feature when positioning.

TEST FUNCTION (S5N-Px...G00)

The TEST+ and TEST- inputs can be used to inhibit the emitter and verify

that the system is correctly operating.

The receiver output should switch when the test is activated while the beam

is uninterrupted.

The inputs activating voltage range is 10 ... 30 VDC.

Datalogic S.r.l.

Via S. Vitalino 13 - 40012 Calderara di Reno - Italy

B01: 0.1...2 m on R2

Tel: +39 051 3147011 - Fax: +39 051 3147205 - www.datalogic.com

C01: 0...35 cm

Helpful links at www.datalogic.com: Contact Us, Terms and Conditions, Support..

C10: 0...8 cm

D00: 0...8 cm

F01/G00: 0...20 m

T01: 0.1...1 m on R2

rights under copyright, no part of this documentation may be reproduced, stored in or introduced into

a retrieval system, or transmitted in any form or by any means, or for any purpose, without the

express written permission of Datalogic S.p.A. and/or its affiliates. Datalogic and the Datalogic logo

are registered trademarks of Datalogic S.p.A. in many countries, including the U.S.A. and the E.U. All

other trademarks and brands are property of their respective owners. Datalogic reserves the right to

make modifications and improvements without prior notification.

SETTING

MIN

MAX

For information about the disposal of Waste Electrical and

Electronic Equipment (WEEE), please refer to the website at

www.datalogic.com.

821005704 Rev. E