DV Mark EVO 1 Gebruikershandleiding - Pagina 5

Blader online of download pdf Gebruikershandleiding voor {categorie_naam} DV Mark EVO 1. DV Mark EVO 1 9 pagina's.

Pagina afdrukken
DV Mark EVO 1 Gebruikershandleiding
26) AC POWER SOCKET Make sure the unit is grounded; all three terminals of the AC power plug must be connected to avoid any
injury to the user or damage to the unit.
The DV Mark EVO 1 is manufactured to be used in the country where it has been sold, and it's factory preset to that country's voltage.
So make sure you're sending the correct voltage to your amp before you connect it to AC power.
27/28/29) SPEAKER OUT Connect your cabinet/s to the speaker out/s (minimum load 4 ohm, the speaker outputs are in parallel).
The speaker JACK outs (27-29) accepts ¼" Jack speaker cables, the SPEAKON (28) accepts SPEAKON speaker cable (either 2 poles
or 4 poles connector -standard wiring +1/-1).
Do not use instrument cables.
The DV Mark EVO 1 delivers 250W of power into a 4 ohm cabinet (or two 8 ohm cabinets) or 150W into an 8 ohm cabinet.
AMP 2
GAIN
10
4
5
AUX
3
ch2
6
30) MIDI IN Connecting the EVO PEDAL to this MIDI input you've access to switch CH1/CH2, turn ON/OFF FX1 and FX2, TURN ON/
2
12
13
OFF the BOOST and the MUTE/TUNER functions.
1
11
ACTIVE
•
The MIDI RX CHANNEL is setted on #0
MUTE
-
19
TUNER
E A D G B E
The switch between channel are setted as for the PROGRAM CHANGE:
4
5
PASSIVE
3
6
2
•
PC#1=Ch1 / PC#2=Ch2
CH2
3
4
1
REVERB 1, REVERB 2, BOOST, MUTE/TUNER ON/OFF are setted as for the CONTROL CHANGE:
ch1
CH1
1
2
AMP 1
GAIN
•
REVERB 1 ON = (CC #1,1) / REVERB 1 OFF = (CC #1,0)
•
REVERB 2 ON = (CC #2,1) / REVERB 1 OFF = (CC #2,0)
•
BOOST ON = (CC #3,1) / BOOST 1 OFF = (CC #3,0)
•
TUNER ON = (CC #28,1) / TUNER OFF = (CC #28,0)
31) USB - This USB port allows to connect your DV Mark EVO 1 to a computer thanks to an USB A/B (printer) cable to set your
preferred AMPs on CH1 and CH2, parameters of REVERB 1/REVERB 2 and virtual CAB/Speaker Emulator (assignable at the XLR Line
Out) using the DV Mark EVO 1 software, and then storing your favorite settings on the amp.
26
LOW
MID
HIGH
LEVEL
14
15
16
17
DV MARK
i
5
6
7
8
LOW
MID
HIGH
LEVEL
27
28
29
MINIMUM
CLASS 2 WIRING
1 + = SIGNAL
LOAD
1 - = GND
4 OHM
SPEAKER OUT
MIDI IN
USB
SEND 1
SEND 2
30 31 32
33
REVERB 2
MASTER
rev 2
18
20
25
on
24
rev 1
boost
9
21
23
22
PHONES
REVERB 1
BOOST LEVEL PHONES LEVEL
•
CAUTION:
FOR CONTINUED PROTECTION
AGAINST RISK OF FIRE
REPLACE ONLY WITH SAME
TYPE AND RATING FUSE.
ATTENTION:
REMPLACER UNIQUEMENT PAR
UN FUSIBLE DE MEME TYPE.
LOOP
GND LIFT
GND LIFT
PRE MIX
+4 dB
RETURN 1
RETURN 2
LINE OUT
LINE OUT
LINE OUT
POST MIX
-10 dB
1
2
34
35 3637 38

REAR PANEL

AMPS SELECTION at DV Mark EVO 1 software
clean
•
TRIPLE 6 CH1 (DV Mark Triple 6)
•
DARKFACE '65 (65 Blackface FENDER
®
•
SLODRIVE US (SOLDANO X88R
CH1)
®
•
ECSTASY CH1 (BOGNER XTC
®
CH1) clean
•
MARAGOLD (DV Mark Greg Howe signature)
•
TOP 30 (Vox AC30)
crunch
•
TRIPLE 6 CH2 (DV Mark Triple 6)
•
ROCK '75 UK (MARSHALL
JCM800
®
®
•
SLODRIVE US (SOLDANO X88R
®
CH2)
•
ECSTASY CH2 (BOGNER XTC
CH2)
®
•
JCMARK (MARSHALL
JCM800
)
®
®
lead
•
RECTO US (Mesa Boogie
DUALRECTIFIER
®
•
SLODRIVE US (SOLDANO X88R
®
CH3)
•
ECSTASY CH3 (BOGNER XTC
CH3)
®
•
PROGRESSIVE (MARK V hi-gain inspired)
•
MARAGOLD CH3 (DV Mark Greg Howe signature)
REVERB SELECTION at DV Mark EVO 1 software
•
NONE (no reverb)/ SPRING REVERB / REVERB
Parameters: TIME / COLOR / DIFFUSION
CAB SELECTION at DV Mark EVO 1 software
•
NONE (no CAB emulator)
•
4x12" VINTAGE 30
®
(Celestion
®
Vintage 30
•
2x12 CELESTION
(Vox
AC 30
)
®
®
®
1x12 JENSEN
(Fender
De Luxe
)
®
®
®
32/34) SEND/ RETURN 1 If you use effect pedals or rack gear, you can route them through
the CH1 using SEND 1 (32) and RETURN 1 (34), connecting the SEND to the input of the effect
and the RETURN to the effect's output using instrument cables.
33/35) SEND/ RETURN 2 If you use effect pedals or rack gear, you can route them through
the CH2 using SEND 2 (33) and RETURN 2 (35), connecting the SEND to the input of the effect
and the RETURN to the effect's output using instrument cables.
36) ) +4 / -10dB Output Level select switch (+4/-10dB) related to the LINE OUT XLR level.
37) GROUND LIFT Occasionally when you're playing live and using the LINE OUT, the
soundman will detect a hum from your amp's signal. This is almost always due to a grounding
problem related to your power source; you will likely eliminate this hum simply by flipping the
GROUND LIFT switch.
38) LINE OUT This output sends the preamp signal to the mixing console, to recording
device, DI, etc. The Line Out signal is post reverb and effects connected to the send/return.
CAB/Speaker Emulator is assignable at the XLR Line Out using the DV Mark EVO 1 software.
TWIN REVERB
)
®
)
)
®
®
)
5