Fright Ideas BooBox Flex Snelstarthandleiding
Blader online of download pdf Snelstarthandleiding voor {categorie_naam} Fright Ideas BooBox Flex. Fright Ideas BooBox Flex 2 pagina's.
Ook voor Fright Ideas BooBox Flex: Snelstarthandleiding (2 pagina's)
Pagina afdrukken
Quick-Start Guide
BooBox Flex
(FI-206s)
MORE INFORMATION ONLINE
This guide covers only a fraction of what the Flex can do.
Tutorial videos and a full manual are available online.
Solid-State Output Wiring Diagrams
12/24 VDC
MUST BE 1.5A OR LESS
DEVICE
(18W at 12V, 36W at 24V)
EXAMPLES OF DEVICES COMPATIBLE
WITH SOLID-STATE OUTPUTS:
LED LIGHTS, SOLENOIDS, RELAYS.
ANY 12/24 VDC LOAD UNDER 1.5A.
1
+
2
3
+
4
ANY 12 OR 24 VDC DEVICE
TO WALL
OUTLET
1
2
RELAY BOARD
3
4
TO POWER SUPPLY
USING A BOOBOX RELAY BOARD
Power Supply
POWER
12-24 VDC
Selecting your Power Supply
The Flex requires a 12 or 24 volt DC power supply. The power terminals on the
terminal block are directly connected to the barrel connector, so you can also
use it to supply or borrow power.
Sizing Your Power Supply
To size a supply you must calculate for the worst-case scenario. Add up the
wattage for the most outputs that will be on at any one time, then add 2 watts for
the Flex. Note that the Flex can't drive more than 5 amps of current total. That
equates to 60 watts at 12 volts or 120 watts at 24 volts.
Example:
2 watts Flex (If using ScareMaster use 5 watts)
+ 18 watts 3 x 6 watt solenoids
+ 1 watt
LED Light
= 21 watts Total - Need at least 21 watts
12/24 VDC
DEVICE
12/24 VDC
12/24 VDC
DEVICE
DEVICE
1
+
2
3
+
4
FOUR 12 OR 24 VDC DEVICES
BLUE = FAST
GREEN = SLOW
1
2
+
RELAY BOARD
3
4
USE OUR RELAY BOARD IF YOU NEED A FEW RELAYS.
TWO CAN BE LINKED TO GET 8 RELAYS
12 VDC MOTOR IN FORWARD AND REVERSE
1
2
3
C
POWER CAN BE SUPPLIED
USING THE BARREL CONNECTOR
OR THE TERMINAL BLOCK.
12/24 VDC
DEVICE
+
1
2
BOOBOX
RELAY
12-
GND
24V
12 OR 24 VDC DEVICE > 1.5 AMPS
TO 12 VDC POWER
FOG
SUPPLY
HIGH
VOLTAGE
+
RELAY
-
1
+
2
FOG MACHINE
Solid-State Outputs
VOLTAGE
IN
About Solid-State Outputs
Solid-state outputs are great for reliably controlling relays, solenoids, and
LED lights. They cannot be used to directly control high-current, 110 volt, or
contact-closure devices like a relay can. However, unlike relays, they have
no moving parts that wear out over time. Use external mechanical or
solid-state relays for high current or high voltage loads. This will result in a
highly reliable and maintainable system.
Dimmable Outputs
Outputs 7 & 8 can be used to control the brightness of LEDs or small DC
bulbs. Use DMX channels 3&4 on the ScareMaster for this purpose.
Solid-State Output Ratings
Each solid-state output can handle 1.5 amps of current steady, or 2.5 amps
in short bursts. The total current on all outputs totalled together must not
exeed 5 amps. Each output is protected from shorts and overloads.
TAKE APPROPRIATE
!
SAFETY PRECAUTIONS
>500mA
WHEN WIRING HIGH
12/24 VDC
VOLTAGES.
DEVICE
1
+
2
ANY 110 VOLT LOAD
FOG
MACHINE
SEE OUR WEBSITE FOR A
CABLE SO YOU DON'T HAVE
4 OUTPUT
TO HACK YOUR REMOTE.
FI-304
OR
1. UNPLUG FOG MACHINE
2. OPEN REMOTE
ADAPTER CABLE
3. LOCATE FOG BUTTON PINS
4. SOLDER WIRES TO PINS
5. CONNECT AS SHOWN
USE ONE OF OUR AC RELAY PACKS WHEN YOU HAVE A LOT
OF 110 VOLT DEVICES TO CONTROL.
VOLTAGE
=
OUT
TO WALL
OUTLET
12/24 VDC
RELAY
COIL RELAY
-
8 OUTPUT
FI-308
1
2
3
4
5
6
7
8
12-24 VDC OUTPUTS, MAX 1.5A EACH, 5A TOTAL
SOLID-STATE OUTPUTS
BooBox Flex
DIMMABLE
PROP CONTROLLER
FI-206s
WWW.FRIGHTIDEAS.COM
SD
CARD
PWR
DMX
PLAY
POWER
DMX
INPUTS
12-24 VDC
5 - 24 V DC/AC
1
2
3
C
1
2
AC RELAY PACKS