DVIGear DVI-3580a Snelstarthandleiding - Pagina 3

Blader online of download pdf Snelstarthandleiding voor {categorie_naam} DVIGear DVI-3580a. DVIGear DVI-3580a 8 pagina's. 4k multiviewer switcher, scaler
Ook voor DVIGear DVI-3580a: Snelstarthandleiding (9 pagina's)

Pagina afdrukken

4K MultiViewer Switcher / Scaler

Installation

For complete operating instructions,

please refer to the User Manual.

1.)

Rack Mount Ears and Removable Feet:

Add or remove these accessories as needed.

2.)

Video Sources and Destinations:

video source device to the HDMI, DisplayPort or VGA inputs on the rear of the DVI-3580a as needed.

Next, connect the displays or downstream devices to the HDMI output and/or the HDBaseT output.

The HDBaseT output only supports extension of audio, video, and POH. The RS-232, LAN, and IR

signals cannot be extended over the link. For best results, DVIGear recommends using CAT-6A F/UTP

(500 MHz) 23AWG high-grade cable or better for the HDBaseT link.

3.)

Audio Sources and Destinations:

accompanying the appropriate video signals as needed. Next, connect any downstream audio

devices to the appropriate audio outputs as needed.

Control Connections:

4.)

Web GUI or Telnet), RS-232, IR Remote Control, and Front Panel selections. The most intuitive,

versatile control method is the built-in Web GUI (see page 7).

To control the unit via the

(straight-through) LAN cable. Set the IP address of the control PC to be within the same subnet

as the unit. Next, open a web browser and input the IP address of the unit. By default, the

unit has an IP address of

address at any time, press and hold the Audio Source Button on the front panel or IR remote for 5

seconds and the current IP will be displayed on the screen.

To control the unit via the

Default values:

Power:

5.)

First, supply power to the

Next, supply power to the DVI-3580a. To do this, plug the AC Power Cord into the receptacle on

the unit and then into an outlet. Switch the unit ON using the master switch on the rear of the

unit. This switch, along with the red power LED on the front panel, will remain illuminated when

power is supplied to the unit and the master switch is turned ON. The unit may need to be toggled

out of standby mode. When the unit is in standby, the standby button on the front panel will light up

green. Pressing this button will bring the unit out of standby.

After the unit is powered ON and is out of standby mode, supply power to the

Note 2 – WARNING: The HDBaseT port is designed to connect to compatible HDBaseT products only (e.g. DVIGear's DVI-

7520-RX). Do not connect any device to the HDBaseT port of this product unless you have verified that it is compatible.

Do not connect any HDBaseT device to the LAN port of the DVI-3580a. Connecting incompatible devices may cause harm

to the devices. Please consult technical support with any questions concerning product interoperability.

Please use the preferred cable termination scheme (T568B) for all HDBaseT connections throughout the installation

(see the User Manual for more information). It is typical for HDBaseT receivers to operate at high temperatures.

Care must be taken to ensure airflow through the Rx unit is not restricted in any way.

Connect each

Connect any external audio sources to the 3.5mm mini-jacks

The unit may be controlled via a variety of options, including LAN (built-in

LAN

port, connect it to the network or directly to a PC using a standard

192.168.100.100

RS-232

port, connect to the unit using a straight-through cable.

baud rate: 9600; data bits: 8; stop bits: 1; parity: none; flow control: none.

destination

Quick Start Guide

and DHCP Mode disabled. To view the current IP

devices.

DVI-3580a

See the warning below.

source

(2)

devices.