DW 7000 Gebruikershandleiding

Blader online of download pdf Gebruikershandleiding voor {categorie_naam} DW 7000. DW 7000 2 pagina's. 7000 series single & double bass drum pedal

Pagina afdrukken

DW 7000 SERIES PEDALS

Remove the pedal and all packing materials from the box, then follow these instructions to set up and adjust your pedal to fi t the way you play.

Section 1: Drive System Adjustments

The Turbo-Style Double Chain & Sprocket Drive System has been factory-set to the

most popular playing position. However, should you desire to change the angle of the

footboard or length of stroke using one of the alternate position holes in the sprocket,

you must fi rst disconnect the master chain link from the sprocket.

1. Use a small screw driver to spread the open ends of the lock ring on the master

link and remove the lock ring.

2. Remove the master link from the sprocket and re-position it in one of the alternate

sprocket holes.

3. Re-attach the lock ring to the master link.

Section 2: Beater Ball Adjustments

2.1: Height

The length of the beater rod can be adjusted to achieve the desired feel and impact

position. Loosen the beater position screw and raise or lower the beater rod to the

desired position and then tighten the screw. Generally, the beater should hit the center

of the drum or an area 1-2 inches above the center.

2.2: Memory Lock

1. Place the beater memory lock loosely on the beater shaft and place the beater shaft

in a normal playing position in the beater hub.

2. Slide the memory lock down the shaft so that it fi ts into the notches on the beater

hub.

3. Adjust the beater to the desired playing position and tighten the drumkey screw

on the beater hub as well as the set screw on the memory lock with the small hex

key wrench (provided). The beater ball should be positioned at a right angle to the

memory lock so that the beater can be reversed from the soft felt to the hard plastic

side by slightly raising the beater and rotating it 180 degrees.

2.3: Playing Surface

The 101 Two-Way Beater (standard) has both a curved, medium felt side for a rounder,

warmer attack and a fl at, hard plastic side for a sharper, brighter attack; much like wood,

but lighter in weight.

Section 3: Slotted Stroke Adjustment

To modify the distance the beater travels during the course of each stroke:

1. Loosen the Stroke Adjustment drumkey screw and slide it to the desired position in

the Stroke Adjustment slot.

2. Tighten the key screw.

Section 4: Spring Tension Adjustment

DW Drum Pedal Springs feature an internal noise reduction damper as well as a tension

locking mechanism. To increase or decrease the spring tension:

1. Loosen the round knurled nut at the base of the spring assembly.

2. Push down on the spring to release the self-locking hex nut.

3. Tighten or loosen the lock nut to create the desired tension, then release the hex

nut and retighten knurled nut to lock in the adjustment.

Section 5: Hoop Clamp Adjustments

The DW Hoop Clamp is designed to fi t a wide variety of manufacturer's bass drum

hoops. To set the space of the hoop clamp for your bass drum:

1. Use the hex key wrench (provided) to loosen the set screw on the knurled nut.

2. Rotate the knurled nut to narrow or widen the gap and re-tighten the set screw.

3. Position the pedal on the center of the hoop and tighten the T-screw securely.

Use the provided rubber hoop protector to avoid damage to your bass drum hoop.

Section 6: Non-Skid Spurs and Velcro™

All DW Bass Drum Pedals include built-in adjustable spurs and non-skid Velcro on

the bottom of the pedal plates to prevent bass drum crawl. The Velcro automatically

grips on most types of carpeting. To adjust the spurs, simply turn the knurled portion

clockwise for more skid control or counterclockwise for less. Be careful when you use

the spurs as they may damage the fl oor.

Two-Way Beater

Double Chain

& Sprocket Drive

Footboard

Heel

7000

Auxiliary Pedal

7002

Double Pedal Linkage Adjustment

Use the provided standard drum key to secure the linkage to the primary pedal by

tightening the key screw on the right side universal joint. Rotate the beater, casting

and hex shaft on the auxiliary pedal to the correct playing position, attach the left

side of the linkage and tighten the auxiliary side key screw. Loosen the two sets of

key screws on the middle section of the linkage and adjust the length and angle of the

linkage to the desired position, then retighten the set screws.

Beater Shaft

Beater Memory Lock

Beater Hub

w/Position Screw

Rocker

Slotted Stroke

Adjustment

Spring

Hoop Clamp

Height Adjustment

Spring Tension

Adjustment

Spur

Hoop Clamp Adjustment

T-Screw

Drumkey

Hinge

Pedal Plate

Double Pedal Linkage

Primary Pedal

Knurled Nut

Hex Nut