AUSTRALIAN MONITOR SM16 Bedieningshandleiding - Pagina 3
Blader online of download pdf Bedieningshandleiding voor {categorie_naam} AUSTRALIAN MONITOR SM16. AUSTRALIAN MONITOR SM16 9 pagina's. Stereo mic/line mixing consoles pro series
Ook voor AUSTRALIAN MONITOR SM16: Brochure (4 pagina's), Bedieningshandleiding (12 pagina's)
Pagina afdrukken
MIC/LINE
INPUT
SECTION
@
uro
{$
r',lrc
Balanced
XLR
input
"@
i:if.,rl""r,*,.
@^,_
For
unhland u*
pi.
1
ad
pin 3
hv€ L b
bndg€d
LIN
E
6.35mm
TRS
input
Unbalan@d use
of
mono
1/{"iack
plugs
TiP =
Signal
Grcund/Shield
@
enr
@
r-ow
cur
FTLTER
swrrcH
@
e*r.r
This switch
will
roll
off
frequencies below
75Hz
at an
18dB per
octave
slope. This
can
be used
to eliminate rumble caused
by
sensitive lectern mics
etc.
i.
i
@ err
The
Pre Fader Listen
(PFL)
switch
is used
to
monitor the input signal
before
the
channel
fader.
This can
be
switched to
either the headphone/local monitor output
or
the master lelVright outputs
(see master section)
\
!
t
@
onrru
This
is
the
initial gain control for each
input
and
should
be set
to optimise
each
inputs level while
still
leaving headroom
so
the input signal does not reach clipping
level.
This gain stage
has a
range from
+10d8
to
+60d8.
EG SECTION
Balanced use
ot
sterco
l//1"
lack plugs
Ring
=
-
Gound
/Shisld
Tip
Ring
For
onndton
of
balaned
ad
unbalaned
plugs, dng and
sleve
have
b
h
bridgsd
at
ihe
sters
plug
This
mid
range E0 control adiusts
mid
range frequencies and
has
a
fixed
2
octave bandwidth
at
2.5kHz.
This control
will
give
up
to l5dB
of
boost
or
cut. The
centre position
will
give
a
flat
response.
$
r-ow
This low frequency shelf E0 control
adjusts
bass
frequencies
and
will
give
up
to
1
5dB
of
boost
or cut
at
80H2.
The
centre position
will
give
a
flat
response.
AUXILIARY
SECTION
@
uroH
This
is a
shelf
E0
filter
that
adjusts treble
frequency levels
and
will
give
up
to
15dB
of boost or cut at
l2kHz.
The centre
position
will
give
a
flat
response.
Aux
1
is
a mono
split
of
the
channel inpul
signal and is post E0 but
pre
the
channel
fader.
@ rosr
Aux
2
is a mono
split
of
the
channel input
signal and
is
post E0 and post
channel
fader.
The channel
pan
control is
used
to posi-
tion
the
channel signal
in
the stereo field.
@
eenrc
r-ro
This red
LED
illuminates when the
channel
is
going into overload (clip)
@
r-evrr-
This channel output fader
adjusts
the
level
of
the channels signal before
it
is sent
to the master output
buss.
PAGE
4
SM12
&
SM16 OPERATION MANUAL